Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 79679278010

79679278010 Kenmore Dryer - Overview

Get Parts and Repair Help for 79679278010

If you know the dryer repair part you need, you can browse the list of all parts on the 79679278010, or you can search by name or part description. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$32.63

Drum Support Roller

This part is sold individually. The drum support roller is found in your dryer. It is used to hold the drum in place in the cabinet while letting the drum rotate on the support rol...

Order within the next 5 hrs and your part ships today!
$5.72

Sensor

The sensor controls the temperature in your dryer and will turn off once your clothes have reached the desired dryness level. If you notice that your dryer is not giving off enough heat to dry the clothes or is taking too long to dry, this may indicate that a repair to the senor is required. To access this part, you will need to remove the front bulk head. To remove this, you will need to remove the screws securing the top. Uninstall the screws that support the control panel and lift. Remove screws holding the support bracket in place so you can detach this piece. Detach the wire harness and remove the wire, then set the bracket aside. You will now open the dryer door and release it by taking out the bottom two screws. Disconnect the wire harness and moisture sensor wire harness, remove screws from front bulk head, and remove screws that secure the duct housing. You should be able to completely remove the bulk head. You will find the sensor underneath the lint filter grill, which will also need to be removed.

Order within the next 5 hrs and your part ships today!
$14.94

THERMOSTAT

The thermostat is a part for your dryer, and it is roughly 1 inch long by roughly 1.5 inches wide. The purpose of the thermostat is to measure the temperature of the air inside you...

Order within the next 5 hrs and your part ships today!
$17.86

Thermistor,NTC

This dryer thermistor temperature sensor helps monitor and regulate the temperature inside a dryer. This part includes the wire harness. If your dryer overheats, does not produce enough heat, or takes too long to dry, then the thermistor might be defective or damaged. This can cause a fault code and could begin either prolonging or shortening drying time. As a safety precaution, make sure to unplug the dryer from the power source before beginning this installation, and wear gloves to protect your hands. Refer to the installation instructions provided by the manufacturer for further guidance.

Order within the next 5 hrs and your part ships today!
$23.47

Filter Assembly,Lint

Order within the next 5 hrs and your part ships today!
$14.73

Cover,Guide

Order within the next 5 hrs and your part ships today!
$4.27

Door Strike

Order within the next 5 hrs and your part ships today!
$59.11

Gas Igniter

Comes with bracket and wire harness.

Order within the next 5 hrs and your part ships today!
$14.94

Thermostat

Order within the next 5 hrs and your part ships today!
$4.27

Leg

Order within the next 5 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

I broke the igniter while adapting from Natural gas to LPG

  • Customer: Nathan from Mount Vernon, WA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
This was a repair from a repair. It started as a conversion to LPG, in the process the igniter broke. The parts arrived quickly and we were able to get it back together and the wife is happy. Thanks. read more

Broke igniter replacing thermostats

  • Customer: Jeff from Ogden, UT
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Unplugged dryer. Removed front panel. removed nut holding old igniter. Unplugged old igniter, plugged in new igniter, and mounted new igniter with screw using nut driver. read more

dryer had lent fire and didn't have heat in the dry cycLe.

  • Customer: Lorinda from DeWitt, MI
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
After replacing the wires and the heat thermostat I realze that I needed to replace the thermostat ntc and the thermostat to blower located under door was burnt during fire. I removed front panel,front facing and tumbler to reach thermostat inter wall. It was easy after fixing to other area prior. I thought it was very easy and didn't cosume much time. I'm a... read more