Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 79640272800

79640272800 Kenmore Washer - Overview

Get Parts and Repair Help for 79640272800

If you know the washer repair part you need, you can browse the list of all parts on the 79640272800, or you can search by name or part description. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for 79640272800 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$40.53

Tub Bearing

The tub bearing supports the spin basket shaft at the back of the washing tub. If your washing machine will not spin, is leaking water, or if there is a loud screeching noise durin...

$31.78

Tub Bearing

This is known as a tub bearing or a rear bearing, and it is part for your washing machine. The function of this bearing is to be a support for the spin basket shaft that is located at the back of the washer tub. This model is sold individually and measures to have a 2.5-inch outer diameter. As this bearing is very difficult to install, the manufacturer recommends completely replacing the rear tub and bearing assembly. If you are only installing the rear bearing, consider replacing the seal and the other bearing as they wear out together.

$11.85

Gasket

If you notice your washing machine is leaking water from the top of the transmission, it might be due to the gasket being damaged or worn down. When replacing your gasket, consider...

$13.88

Locking Pin

This is a locking pin, and it works in conjunction with your washer. The part measures to be roughly 3 inches long, and less than an inch wide. The pin is cylindrical, off-white in color, and made entirely of plastic. This part is used to hold the shock absorber on the washing machine. There is a pin used at the bottom and top of the shock absorber. This model is sold individually. If your washing machine is experiencing an above-average amount of shaking and moving this part may be the reason.

$21.90

Tub-to-Pump Drain Hose

This is a tub-to-pump drain hose for a front load washer. The hose features flexible bellows which allow it to expand and contract when necessary. It carries the water from the tub...

$11.85

Box Assembly,Detergent

$11.85

Gasket

This is a seal for a washer tub. It creates a seal between the front and rear halves of the washer tub to prevent the appliance from leaking. If you notice leakage between the two ...

$79.19

Door Gasket

Also known as a door boot seal or bellow and comes with a drain hole.

$29.56

Sensor Assembly

$99.45

Spider

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Bellows had developed a small hole

  • Customer: Verle from Malcolm, NE
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed the old bellows (2 squeeze hose clamps and one screw adjustable hose clamp) slid on the new one and it was done! read more

Unit would not start up

  • Customer: LES from GAINESVILLE, FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
Conclusion was that either the control panel or the noise filter (an electrical fuse apparatus)was bad. Disconnected the water line, turned off power, and pulled unit out from cabinets. Determined that voltage was going into the noise filter (white harness) but almost no voltage coming out (red harness). Ordered noise filter. Hardest part was removing old no... read more

Washer will not power on

  • Customer: Robert from Damascus, MD
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Disconnected power. Removed washer top; only 2 screws in back. Disconnected two wire connectors on Filter Assembly Circuit. Removed assembly; 1 screw. Installed new assembly, reconnected wires, and replaced washer top. read more