Models > 79573139410 > Instructions

79573139410 Kenmore Refrigerator - Instructions

All Instructions for the 79573139410
1 - 15 of 16
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
replace leaking water inlet valve assembly
1. Shut off water to refrigerator. 2. Removed bottom sheet metal cover (6 screws). 3. Removed leaking water inlet valve assembly from refrigerator (1 screw). 4. Remove water inlet tube (loosen nut) and tube back to refrigerator (pull from water valve after remove cotter pin washer). 5. Detach two electrical wire harnesses. 6. Install new water inlet valve assembly to refrigerator (1 screw). 7. Replace both water tubes to water inlet assembly. 8. Re-attach both wiring harnesses. 9. Turn water to refrigerator on. 10. Check for leaks. 11. Re-attach bottom sheet cover (6 screws).
Parts Used:
Water Inlet Valve Assembly
  • Richard from JACKSONVILLE, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
28 of 48 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken shelf glass
Just popped the new one in. Followed the online instructions.
Parts Used:
Crisper Shelf Glass
  • george from PARAMUS, NJ
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
5 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Low water pressure which in turn led to no water and no ice.
Unplugged fridge, shut off water supply disconnected water supply from fridge. Remove screws that hold lower cover on back of fridge, removed screws holding valve assembly to fridge. Disconnect two electrical connections, remove black c-clip on out flow water line, lift fitting on outflow line side and pull water line off. Replace with valve assembly in reverse order
Parts Used:
Water Inlet Valve Assembly
  • Daniel from ABERDEEN, WA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers, Wrench set
7 of 14 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
roller was missing in freezer upper drawer
easy, just lift the drawer and insert the roller assy.
Parts Used:
ROLLER ASSEMBLY
  • Bob from LIBERTY TWP, OH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Ice bucket broken
Replaced with new bucket
Parts Used:
Ice Bucket
  • EDWARD from ASSONET, MA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Leaking
Swapped old one with new one. New one had extra plug not needed.
Parts Used:
Water Inlet Valve Assembly
  • Johnny from MOUNT OLIVE, AL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fridge door wouldn’t shut
Took old door strip (spring broke) and installed new with spring It went well and was working in less than 5 minutes
Parts Used:
FRONT PLATE ASSEMBLY
  • Judy from EGG HBR TWP, NJ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Spring broken on front plate
Unscrew two Phillip screws on center hing , push frt plate down and replace.
Parts Used:
FRONT PLATE ASSEMBLY
  • RODNEY from GERMANTOWN, TN
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Ice Maker and Water dispenser stopped working
Pulled the fridge out.
Unscrewed the back cover and the one screw holding the value assemble.
undid the 2 hoses and replaced the part.

Super SImple/
Parts Used:
Water Inlet Valve Assembly
  • Donald from BETHPAGE, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Cold water control rusty and leaking water
Removed old part very easily and installed the new part without any problems. Used and adjustable wrench and screwdriver
Parts Used:
Spring,Lever
  • Homer from MARION, VA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers, Wrench (Adjustable)
2 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Ice Maker failed, freezing up all the time, Leaks water..
Followed steps that i seen on YouTube. lol
Parts Used:
ICE MAKER ASSEMBLY,KIT
  • MICHAEL from COMMERCE CITY, CO
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Slow water for drinking
Just like on YouTube very easy to do
Parts Used:
Water Inlet Valve Assembly
  • Steven from SEBASTIAN, FL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Wrench set
1 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Valve assembly leaked
The assembly sent is different than what is on the unit. The connectors do not match. We called and it seems you don’t have the correct part. The only part we have found will only connect the ice maker or the water. It will be a shame if I have to buy a new refrigerator.
Parts Used:
Water Inlet Valve Assembly
  • Richard from TORRANCE, CA
  • Difficulty Level:
    Very Difficult
  • Total Repair Time:
    More than 2 hours
2 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Spring was broken on original unit, had to replace whole lever.
removed old lever ( 2 screws ) took apart electrical connection, replaced lever, connected electrical hookup, put in screws. DONE !!!!!!
Parts Used:
Spring,Lever
  • Alan from Sun City West, AZ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
plastic tube leaking at connector
Uncoupled the old connector, replaced with new connector and attached supply line. Repair easy with right part, prior to ordering the right part I had tried a compression fitting and it still leaked. U-tube and others demonstrating repair assured me I was on the right path.
Parts Used:
Holder,Bracket
  • GREG from STILLWATER, NJ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Wrench (Adjustable)
1 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 79573139410
1 - 15 of 16
Back to Top