Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Broken water line
Remove water filter and water filter holder. Removed cover on back of frig. Removed clip where water line connects to back of water filter. Took half inch wrench pushed in on water line lock to release line. Repeat at other end. Reverse steps to put on new line. Easy repair.
Water feed line running from water valve to filter housing was leaking
Shut off water supply. Disconnect main supply line. Remove rear lower panel on back of refrigerator. Remove all tubing clamps on back. Disconnect leaking tubing from water supply valve. Remove water filter and unscrew/remove water filter housing. Replace tubing - connect to water filter housing then to water supply valve. Reconnect filter housing and filter. Reinstall lower panel, then main water supply line, then all tubing clamps. Turn water back on and check for leaks after discarding several glasses of water to fill filter. Job complete!
1) Removed the screws from lower back plate 2) Removed the screws holding the plastic water lines in place (little plastic brackets - several of them) 3) Take a picture of how the tubing and what hose goes into what part - the 5/16" hose can go into 2 different spots - I didn't do this and I had to fix this 4) Pull out the hose "tabs" that lock the clamp into place (several) 5) Push in new hose 6) Put in clamp 7) I had to remove the filter on the inside of the fridge. Remove the filter, there is one screw that comes out, then you will have access to the hose clamps 8) Repeat for all the other hoses 9) Put the plate and brackets back into place (the picture really helps on how to orient and route the 3 different tubes 10) Test the water 11) Crack open a beer for a job well done
Super easy - take a picture! It will save you time!
Icemaker quit releasing ice from tray and water was pouring and freezing in ice storage bin
This couldn't have been easier. Two tiny screws in the front needed unscrewed, and then two plastic clips in the middle just had to be popped lose. Finally, you unplugged the power cord. Then, you just needed to reverse the process by plugging the new ice maker in, popping the clips in place, and screwing the two holes back in and turning the whole thing on. Voila! Perfect ice cubes again. And for only a little over $100.
Very bad noise which stopped when the door was opened
The Refrigerator now runs very quite. After watching several videos I started on mine and found that it was a bit different than any in the videos. However all but the back panel was shown and that was helpful. The back panel was a bit difficult but a hair dryer seemed to help . All in all it was a good choice to do it myself as it was done quicker than waiting on a repair man.
An easy way to get a refrigerator out from the wall is to use a tow strap or 1/2 to 3/4 in. rope. Throw a loop behind refer while keeping both ends in your hands. Let it settle down to the lower half of unit and pull using both hands. Comes right out. Remove lower panel. Unscrew water valve from cabinet. Remove all tube holders Lay some rags down to catch a little water drainage. Turn off water supply valve at wall. Unplug Power. Remove filter and filter holder. (one screw). remove tube from valve by removing plastic C clip. Push plastic ring towards the valve and pull out tube at same time. With the tube free, remove filter, then mount screw to remove the inside filter holder. When it is out, pull the tube doing the same process as the lower end. Pull tube out and replace with new one putting everything back in reverse order. Before placing tube holders back on, turn on water to check for leaks. After turning water back on and plugging in power, push refer back into place. While I was there, I also replaced the hose from the wall to the refer.
Remove 2 screws and then disconnect wires to the bulb sockets. Reconnect the wires Reinstalled lamp case , tab end first then replaced the 2 screws and the Lens cover. In addition, I changed out the incandescent bulbs to a much cooler LED bulb.
The heavy work is moving the fridge, then take off the lower plans. Use a bowel or cup for screws and the water line connector spacers so you don't loos them. undo connections holding water line, including the bottom brakes for the solenoid. Reuse the spring around the lower waterline to prevent external wear on the line.
NOTE: remove the waterline connector spacers and save! NOTE: you must compress (not pull) the connect to then pull the waterline out of the connectors. NOTE: You must also remove the water filter and housing inside the fridge but this is easy. MOTE: Test the line for leaks by turning on the water and then using the door water. The filter will need to refill so it may take a minute before water comes up. This line only have pressure when the door water is used or the ice maker needs to make ice.
After replacing the line, test the line for leaks by using the door water so the solenoid fills the lines
Unplug the refrigerator and empty the freezer. Remove the lower basket and roll out upper tray. Open the freezer door. I was able to lie on the floor to remove the 2 screws holding the ice maker without removing the freezer door. Depress the 2 tabs and slide the ice maker forward to remove. Install in reverse order. Change the water inlet valve at the same time.
Ice crystals appearing on the face of the freezer draws
Part Select had a great video which made the repair easy, using a putty knife to start removing the freeze door gasket. Once removed the install is simple just snap the new gasket into the track, but start at the corner. Other company's have a video requiring you to remove the entire freezer compartment out of the appliance, unnecessary waste of time and labor.
Replaced old hose and installed the new one. Was very simple with the instructions in your email..... step by step, could not of been any similar.... you guys rock
The past I ordered was broken upon delivery. I asked for a replacement and was refunded the charge. Tried to contact you but "due to covid" you aren't taking calls. Net result: I ordered the part from another source, got it, installed easily. Won't use you again.
Now that you have to buy a complete assembly that includes the drawer in the classy window it's very simple to replace however you buying parts that you don't need simply because G no longer makes the window. Which I find rather odd being as though that they make the whole assembly think and sell windows by themselves for less than 2/3 of what I spent through the whole assembly
Wrong parts sent twice. One of the parts was a substitute 2" too long
Unable to complete repair, had to send parts back Part should have been PS11732074, but got PS11732704- wrong part This was a substitute part and was 2" too long
Waiting for refund on this part. It cost me $14.50 to return it by UPS!!!