Models > 79096011400 > Instructions

79096011400 Kenmore Range - Instructions

All installation instructions for 79096011400 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 79096011400
76-90 of 469
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Element cracked and sparked, no longer functioned

  • Customer: Steve Gilliland from Delavan WI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 1 of 1 people found this instruction helpful
I UNPLUGGED the oven (very important), then I removed the two screws that hold the element in place, pulled the element out far enough to disconnect the two wires, plugged the wires on to the new element, pushed the new element back into place, and replaced and tightend the two screws. Finally, I plugged the oven back in.

baking element out

  • Customer: PAUL from FRANKLIN NC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
removed the two screws pulled the wires out sliped the connections from the old element and connected the new one .

ELEMENT WAS SPARKING AND COAL HOT RED

  • Customer: MIRANDA from INDEPENDENCE KY
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 1 of 1 people found this instruction helpful
UNPLUGGED OVEN, PULLED OUT OLD ELEMENT, REATTACHED NEW ONE, MAKING SURE TO BE CAREFUL WITH WIRES, AND PUT ON AS SECURE AS POSSIBLE, JUST LIKE IT WAS BEFORE...VERY EASY TO FIX

bake element burnt into

  • Customer: don from whiteville NC
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 1 of 1 people found this instruction helpful
i removed the back panel removed two screws pulled the element out

Bake element broken

  • Customer: Richard from Campbell CA
  • Difficulty: A Bit Difficult
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 1 of 1 people found this instruction helpful
Removed screws. Tried to pull out old element but spade lugs on old element were bent at ninety degree angle. Once I figured that out I was able to manouver the old element out with the attached wires. Had to be carfull that the loose wires did not slip back ijn through the hole. Reaching in over the oven door was a but diffcult, but all-in-all the jobe was done in a few minutes.

bake element burned up

  • Customer: charles from cartersville GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 1 of 1 people found this instruction helpful
removed two screws pulled element out about four to five inches attached wire to new element screwed back in less than ten minutes done

Oven would not heat, broiler still worked.

  • Customer: Eric from Lafayette IN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 1 of 1 people found this instruction helpful
I unplugged the stove for precautionary reasons.
I then removed the two screws holding element in place with the correct nutdriver.
I then carefully pulled out the element and pulled the two female spade connectors off.
I then compared to new element and plugged the new element in.
Finally I screwed in the new element and tested the oven.
It worked again!! I would recommend running the oven for a bit before placing anything in to bake. this allows burn off of stuff on the new element.

oven wouldn't heat

  • Customer: Michael from Goddard KS
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 1 of 1 people found this instruction helpful
using a nut driver I removed to two screws that were holding the element in place. Then simply disconnected each wire. Removed the old element and plug the new wires onto the new element. Reinstalled the two screws and everything works fine

bake element arched and caught fire.

  • Customer: Marie E. from Delray Beach FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 4 people found this instruction helpful
i called Sears and ordered the element and they charged me 16.99 plus the part to ship the next day. after 1 week i called them and they said the part was on backorder. i then check with them each week almost a month and the part was still on back order, I asked if they could fix it faster if they came to the house, they informed me it would cost 65.00 for a repair person to see what part i needed and after that they would schedule m e for a repair when the part came in. meanwhile i could not use my oven. i happened to go on line and came up with your web site. i ordered the part and 2 days later my son installed it. my oven works great . your company is awsome.

oven wouldn't heat

  • Customer: Rosemary from Oak Park MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 1 of 1 people found this instruction helpful
I removed the 2 screws, making sure not to drop the wires attached. Took off old wires ,then put new wires on new element, screwed it back into place and it was working. sooooo easy!!

Oven would not heat up-

  • Customer: Charles from Hagerstown MD
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 1 of 1 people found this instruction helpful
Disconnected the main electrical plug from the wall for the oven..
Used a nut driver to remove the two screws that held the heating elementin place.
Pulled the element out so I could remove the two wire terminals.
Installation of the new heating element was fairly basic..Oven is working great..

Original Elememt went bad

  • Customer: Steve from Orefield PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 1 of 1 people found this instruction helpful
The directions have been stated many time and they are quite simple. Take out the two screws, pull the element so the wire connections come through into the oven. Disconnect the element at the wire connectors and replace. This is a dirt easy job.

The only real area for a potential problem is pulling the wire connectors through into the oven. As long as you pull slow and from the back - right next to the whole, you will be fine. Take the connectors off carefully and you're golden. Easy job.

Replace the bake element

  • Customer: Michael from Fort Worth TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
Had to remove the old element and had problems with the element shorted on the quick disconnect. After having my son unplug the appliance and cutting the quick connect off. My son then installed a new quick disconnect and the bake element.

While baking cookies I looked in the oven only to find the bake element was glowing white on the curve of the element, then a second spot started to burn. The element was fried.

  • Customer: Angela from Ruidoso NM
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 1 of 1 people found this instruction helpful
The repair took less time than finding the model number. After unplugging the range and allowing it to cool I disconnected the element (2 screws), went online and found Part Select ordered the element and saved $16.00 dollars over the least expensive local shop, I was amazed at how fast the element arrived, I believe it was 4 days from order to my door. I went to my local hardware store for some new connectors for the wire, put them on and plugged in the element fastened down the two screws and went back to baking cookies. The element was well and safely packed and came in perfect condition. It works like a charm. Thank You

bake element had stopped working

  • Customer: lynne from pelham NH
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Socket set
  • 1 of 1 people found this instruction helpful
My husband had recently moved out of our house so I was very nervous about trying this repair myself but it was actually very easy!!I ordered the part on Monday, it arrived on Wednesday and Wednesday night I was baking dinner in the oven!!
All Instructions for the 79096011400
76-90 of 469