Models > 79095042503 > Instructions

79095042503 Kenmore Range - Instructions

All installation instructions for 79095042503 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 79095042503
16-30 of 191
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

If burner was placed on HIGH, it wouldnt lower heat once LOW setting chosen

  • Customer: Juilo from Lake City FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 17 of 18 people found this instruction helpful
I had to replace the switch in the back of the control knobs. I was very grateful to the female phone attendant who answered my call. Since my part number had switched a few times, she took the time to reverify the "blueprints" of my machine with the parts carried at Parts Select and she helped me be assured that I was buying the correct part for my machine. She was SOOOO helpful. Will definately buy again from your store.

Cord was not tightened enough by delivery crew.

  • Customer: Timothy from Spring Valley AL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 26 of 48 people found this instruction helpful
PF alarm appeared on display. Noticed clicking when cord was moved. Had arced for some time and melted original block. New part slightly different. Only has 3 lugs, old one had six. Stack using washers provided. Take note of colors before disassembly. Use caution while working through access opening. The edges are sharp. Only tools needed are phillips screwdriver, deep socket for lug nuts. Nut driver optional. Hope this is helpful.

anti-tip bracket not installed

  • Customer: Brian from Panama City Beach FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 14 of 17 people found this instruction helpful
I was selling my home and did not realize that the anti-tip bracket was not originally installed. A home inspection caught the problem and the buyers required that I install one. I could not find the original and obviously the installer never put it in place to begin with. The buyers wanted this resolved within a week so I had to act fast. I could not find one locally so I found what I needed on your website. It arrived in a couple of days and was easy to install. I used the template provided in the kit and drove the screws through the bracket into the wood plate behind the drywall. Pushed the range back in place and that's it. Couldn't get any easier.

SWITCH WAS MAKING A ARCING SOUND WHEN BURNER WAS ON

  • Customer: Gerald from Paris TN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 19 of 33 people found this instruction helpful
REMOVED THE BACK COVER OF THE RANGE. REMOVED THE KNOB FROM THE FRONT OF THE SWITCH. REMOVED 2 SCREWS HOLDING SWITCH TO RANGE. REMOVED WIRES ONE AT A TIME AND CONNECTED TO PROPER POLES ON REPLACEMENT SWITCH AND REINSTALLED NEW SWITCH ON RANGE

missing oven racks

  • Customer: ALLAN from APACHE JUNCTION AZ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 12 of 12 people found this instruction helpful
order pcs fit perfect.

burner would not heat

  • Customer: Ed from Winthrop MA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Socket set
  • 11 of 13 people found this instruction helpful
killed the 50 amp power. removed 3 screws from above oven door slid out cook top, dropped brace holding 2 front burners. The connector corroded off had to look for a high heat connector to connect to the element, after that just screwed everything back together.

Front Burner was on high all the time when on

  • Customer: Gregory from Monument CO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 10 of 11 people found this instruction helpful
Turn off the breaker to the stove. Very important because when you move the control panel around after removing it, you can inadvertently touch a hot wire to a grounded metal part on the stove. Remove the 3 nuts from the back of the control panel and the two nuts from under neath the control panel on either far side. Pull the control knob off by pulling straight away from the control panel. Remove the switch by unscrewing the two screws. Match the 5 wires from the old switch to the new switch by removing one at a time and paying attention to the labeling of each on both switches. Reassemble in reverse order. Turn breaker back on.

Large burner wouldn't heat

  • Customer: Phyllis from Elberon IA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 13 of 25 people found this instruction helpful
Removed back off of stove. Removed two screws that held in the switch, removed the wires that were connected to the switch and replaced the part.

Burner failed due to poor manufacturing quality

  • Customer: LaVern from Cedar Falls IA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 8 of 11 people found this instruction helpful
Disconnected power. Removed hold down fasteners for stove top. Fortunately, I did not flue down or use the double back tape to secure stovetop to counter. If this adhesive were used, it is possible I would have had great difficulty in removing range. I did not disconnect the wiring, but turned the range top over to access the cover. I removed the cover and easily removed the failed burner and installed the new ones. I had to pull 4 wires from the terminal strip and reattach them. The hold down strap for the burner was reinstalled. Range top turned back over and fastened down. Back in service.

Bake element burned in 2 pieces.

  • Customer: Mary from Cabot AR
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 6 of 6 people found this instruction helpful
Easy repair. Removed 2 screws and connectors, replaced . (Just a Note) Stove has been a lemon since purchased. Only 3 years old and have already had to replace timer, burners, oven door hinges, and oven lower burner. I'd have been better-off buying a good quality appliance in the first place. Have had many problems and finally replaced 3 year old Frigidaire refrigerator. Same quality issues. Replaced dispenser circuit, defrost circuit, then compressor. Lost a fridge full of food 2x. Under warranty but a real hassle. I will never buy another Frigidaire product.

Oven racks rusted

  • Customer: Wendell from Ocala FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 10 of 19 people found this instruction helpful
Ordered new racks and replaced them.

The stupid baking element died on CHRISTMAS EVE!

  • Customer: Minda from Madras OR
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 6 of 7 people found this instruction helpful
My husband removed the old one in a few minutes, the just popped the new one in when it came. Not for nothing, (where we purchased the stove) wanted $67 for the same part you all charged $49.00

Oven Racks needed to be replaced.

  • Customer: Peter from Chicago IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 5 people found this instruction helpful
Slide out the old; slide in the new!

In a seasonal house, a mouse got into the oven insulation during the winter. We have gotten rid of the mouse but when we used the oven we could smell mouse urine! Upon inspection we could see that the mouse lived and urinated in the oven insulation.

  • Customer: Susan from Newington CT
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 5 of 5 people found this instruction helpful
My husband removed the screws that held the top of the stove on and then lifted the top up. It is hinged. He then took out the old insulation, wiped down all visible parts of the interior with a bleach solution and replaced the blanket insulation with the new insulation. That took care of the problem!

Lens missing for burner "on" indication

  • Customer: Carol from Houma LA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 6 of 8 people found this instruction helpful
Lifted the oven top, removed the controls cover, slipped the lens into the hole and slid the light holder device onto the lens
All Instructions for the 79095042503
16-30 of 191