79095042503 Kenmore Range - Instructions

I followed directions for replacement of the glass from the web. Replacement was simple and easy.

It took about 3 years to order and 3 minutes to fix. forgot to turn off "easy" video on conputor. Wife watched was mad........... for taking so long to fix. 41 years married, any video to fix wife and get me to 42 years as easy as changing draw glides? Thanks Jon

After making sure it was the switches themselves not the burners that were the problem, it was easy locating the exact parts I needed on PartSelect and the shipment arrived in a timely manner. I had to replace two out of four switches. Using a screwdriver, I detached the display pannel and removed the faulty switches. Then I disconnected the old wires and attached them to the new switches, one at a time. Closed everything up and the "new" range works great!

After watching the videos on removing and replacing the front and rear glides on the bottom drawer, I was able to take the bottom drawer out, use a screwdriver to pry all the glides out of their slots and snap them all back in place in less than a minute. Without the videos I was completely helpless in knowing the sequences to performing this task.

Pulled stove away from the wall and unplugged it. Removed probe and cut the wires because the connection clip on the new probe was different from the original. Leave the wires as long as possible because you will need the extra length to splice the clip from the old probe to the wires on the new one. Replaced probe and plugged the oven back in. Done.

The repair was easy.it took only minutes to install.The how to video was a big help.thank you parts select!

Inserted the new rear drawer glides

the rear glides were missing on the back of the drawer so the drawer would pull out but when pulled back in, would tip down and not catch on anything. I ordered the parts then found an instructional youtube and watched it. Easy repair, cheap!

Easy to put in but i droped a screw to hold the element. had to pull another screw to fix it

I read other experiences on line and determined that it was either the element of the control switch. So I decided to order the control. When deciding I had removed the upper back sheild and put it back on. Subsequently a couple of days later there were popping noises culminating in a flash and the stove went 'dark'. I figured that I had pinched a wire when I put the upper shield back on. I removed the shield and looked for black 'short' marks. None were visible. I went to the electric panel and tried to reset the 60 amp breaker. It wouldn't reset and momentarily the lights dimmed. Uh-oh! Went back to stove and opened area where the cord connects to the stove. Direct short- a lose terminal block bolt had welded itself to the chassis! I redid all connections and lined inside of stove back with duct tape- also redid the connections with bolts, nuts and lockwashers covered each with electrical tape. Now reconnecting electric I put the new switch in. Removed the knob from the front and started to transfer the wires from the back. This was a little confusing because the control I received looked different from the one in the stove. After some checking I looked closely at the terminals on each control and they had tiny number/letters on them like H1, Li, H2 etc. So I just transferred H1 0n one cntrol switch to H1 on the new switch- L1 to L1 and so on. Put it all back together, turned on power and everything is working great.

Took a set of pliers and popped the old ones out and snapped the new ones in

Easily repaired.

Emptied the drawer of storage items. Removed the drawer and attached the new rear drawer glide. Replaced the door in the range and refilled the drawer.

Just moved into this house and inherited the oven so I don't know how old it is but I had to put something down in order to submit this review. Popping the glides in place took seconds. I am amazed that I found the parts so easily online and that they arrived so quickly. Usually the simplest of things turns into a time consuming project for me. Thank you!

Took back cover off 2 screws held the switch then moved wires one at a time from old switch to the new one put everything back plugged in stove everything worked