Models
>
79078402011
79078402011 Kenmore Range - Overview
Sections of the 79078402011
[Viewing 5 of 5]
Manuals & Care Guides for 79078402011
Click to downloadInstall
Installation Instructions
(5.65MB)
Install
Installation Instructions
(2.92MB)
Manual
Owner's Manuals
(4.71MB)
Keep searches simple, eg. "belt" or "pump".
LP Conversion Kit
PartSelect #: PS3633782
Manufacturer #: GRLP4
The LP conversion kit is used in ranges
$78.59
In Stock
CAP
PartSelect #: PS11775705
Manufacturer #: 5304508442
The surface Meduim 9.5K burner cap is located on the top of the burner head and is used in ranges and ovens. The burner cap helps spread out the burner flame for even heating, and protects the burner...
$24.35
In Stock
CAP
PartSelect #: PS11775704
Manufacturer #: 5304508441
Sold individually. This part helps the flame to spread for even heat. Also protects your burner head from spills.
$30.07
In Stock
Steel Washer
PartSelect #: PS436497
Manufacturer #: 316008401
This steel washer is also known as the range washer and is used on your oven door. The measurements for the steel washer are a three quarter inch outer diameter, and a one quarter inch inner diameter....
$11.23
In Stock
Igniter/Orifice Mounting Screw
PartSelect #: PS440022
Manufacturer #: 316240600
This part is the igniter/orifice mounting screw for your cooktop or range. It is approximately ½ an inch in length and is made of metal. The mounting screw connects the orifice to the cooktop. If the ...
$12.23
In Stock
Grate Foot Kit
PartSelect #: PS2373826
Manufacturer #: 5304475129
This kit includes 8 rubber feet and adhesive. This surface burner grate pad set is for ranges.
Surface burner grate pad set contains the four pads that attach to the bottom of the burner grate to p...
$72.95
In Stock
CAP
PartSelect #: PS11775706
Manufacturer #: 5304508443
This black burner cap is a genuine OEM part made of a durable material capable of reaching 14,000-BTU, with an approximately 3-inch diameter. It is compatible with various models of ranges and cooktop...
$35.49
In Stock
Burner Mounting Screw
PartSelect #: PS2361437
Manufacturer #: 316540900
Sold individually.
$11.75
In Stock
Questions And Answers for 79078402011
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the 79078402011
[Viewing 2 of 2]Gas igniter glows, but will not light
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
oven bottom had foil stuck on it would not come off
First I removed the two screws that hold the bottom panel I then pulled the panel out and put the new panle in and put the two screws back in
Parts Used:
-
ronald from brownsburg, IN
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
15 of 18 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
replacing the fan on a convection oven (fan was making a vibration noise)
This was the first time replacing the fan. It is a lot easier to work in the oven compartment with the oven door removed, only two screws on the door and the hinges were released. I found that a couple of the screws were either rusted or stripped so I used a pair of pliers to remove the screws that were holding the diffuser in place. O
... Read more
nce there was access to the fan I found that the fan was warped and that the blades were scraping against the back wall of the oven. The next challenge was to remove the retaining nut. I used a sheet metal screw to secure the warped fan to keep it from spinning. once I figured out that you have to turn the retaining nut to the right to loosen, it came off easily. 1/2" socket with extension. When I replace the fan I used two washers for spacers to make sure that the fan would not scrape the wall of the oven. Its been tested many times and the oven does not make that horrible sound anymore.
Read less
Parts Used:
-
John from Stevensville, MD
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers, Socket set
16 of 23 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
replace bad oven ignitor
Oven ignitor is on the bottom gas unit. Ignitor is in oven and plug is in warmer oven on left wall at very back of warmer oven. It has duel function to light both upper and lower gas burners (in oven). Wires of new plug that I received were shorter than existing wires and would not reach the plug from ignitors center mount location to
... Read more
plug at far back of warming unit on left wall. Even if the wires would have been long enough, I couldn't figure out how to "release" the existing plug. Easy solution: Cut old wires at junction of old ignitor (leaving wires as long as possible). Cut new wired as close to new male plug as possible (leaving wires as long as possible on new ignitor). Strip ends of old and new wires and wire nut with porcelin wire nuts (hardest part of job was locating porcelin wire nuts)! After placing wires out of the way of burner and ignitor, reassemble stove parts. AVOID touching new element as oil from hands will decrease the life of the element. Good Luck..
Read less
Parts Used:
-
Mike from PROVO, UT
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
9 of 10 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!