79049612318 Kenmore Microwave - Instructions

PF alarm appeared on display. Noticed clicking when cord was moved. Had arced for some time and melted original block. New part slightly different. Only has 3 lugs, old one had six. Stack using washers provided. Take note of colors before disassembly. Use caution while working through access opening. The edges are sharp. Only tools needed are phillips screwdriver, deep socket for lug nuts. Nut driver optional. Hope this is helpful.

I first removed the top plate above the microwave door (3 screws), then I removed the plate containing the buttons and clock. The microwave has 3 relay switches and they are in a little holder. The holder was too difficult to remove so I just removed the bottom switch and replaced. The microwave started right up.

Repair was quite easy, as long as you have the instructions for removing the door. The screws that hold the bottom of the door to the fixed hinge are placed into the side of the hinge assembly after removal; this holds the door at a 45 degree angle for easy removal. After that, just place the door on a flat surface and dismantle the door from the inside. The inner glass is contained in a metal frame with another piece of glass; this frame comes apart easily using the clips in each side. The door assembles easily after the glass is replaced; just take your time and give yourself enough room to lay out the parts as you go. Good luck!

Removed the 3 screws to drop the lower panel and, removeed the turn table plate and ring. Then removed the 2 screws holding the motor, the 2 wires attached to the motor and removed the old motor.Replaced the new motor in the reverse order. DO NOT FORGET TO UNPLUG THE MICROWAVE FIRST.

was told buy a repair person to check the door micro switches as it was a common problem. removed the top plastic air grill to get access to the screw that holds in place the control cover. After unplugging the unit, i took out the (2) screws that held in the switches and removed them (3). One switch was a bit melted so i tested it with a 12 volt battery and it was bad. Ordered a new one from Part select and got it fast . Works great .

Had to reference original owner's manual for instruction(s) on how to remove oven door. Used several "YouTube" videos to reference oven door design (Oven door glass is actually several layers of glass.) After completing about 30 mins of research and finding the right square drive bit, the repair went smoothly and without complications. The biggest challenge was researching and understanding what part(s) were needed and how to replace them. It seemed liked a lot of work doing the research however it sure beat a $350 repair bill. It cost me $90 and about 1 1/2 hours of total time. Oven works better than ever, thanks parts select for the part(s) and diagram(s) ...

After unplugging the unit remove the control face buy removing the screws. All three door switchs are on a bracket on the left. Remove the two screws holding the bracket in place and pull out. Disconnect the wires from the three switches and test each switch indivually to determine the bad one. I used a multimeter set on ohms.Replace the bad switch with the new one and replace all the wires. Reassemble the unit and you are good to go.

It is a undercabinet stovetop microwave. First had to take it down and unplug. Remove the top cover locate the door switch. Used neednose pliers to remove switch. Unplug two terminals.Plug new switch and use pliers to replace back @ same position.Plug in socket temporarily to see if it works.Afterwards if it works.Unplug and replace cover.Ready to be replaced back under cabinet.

Have a double wall oven and the top oven would not shut off or broiler part would stay on and burn tops of food. Since bottom oven was not having any issues felt like it could
Not be control panel so decided to try the temp sensor. Since replacing oven has worked properly.

first of all, ordered the right piece, second, brought the right handyman to help...getting the over/microwave out as one piece took some doing...then the cover of the microwave had to come off...once we got to the piece itself, it was no issue... then putting it all back together...took about two hours...he needed our assistance because of thew weight and the need to pull the units out simultaneously

As this microwave is part of a wall micro/oven combo, we removed the trim, slid out the microwave and tried for days to figure out how to release the microwave control panel. Through sheer force, we were able to release the lower half of the panel...enough to get our fingers, chopsticks and a flashlight inside to remove the broken lever. It took 2 of us to pull the panel out and replace the lever. I was hoping for a video online of how to remove that control panel but luckily we changed out the broken lever and it's back in working order! Glad we didn't have to trash and entire microwave/oven combo for one broken plastic part...it all works fine now.

Installation of the temparature sensor, one of the technician recommended parts took no time, just two screws and a snap off/snap on part. It did not fix the problem. I then replaced the main control panel, which requires more work, but didn't solce the ussue either. I then replaced the thermal fuse, which wasn't mentioned by tech support, and required much more disassebly of the top panels of the stove, with still no fix to the problem. I am waiting to replace the thermostat heat sensor unit, the only other part in the circuit controlling power supply, requiring removal of the stove top again,

Watched the repair video on your web site. Used the video as a step by step guide in the actual repair.

Remove microwave from wall, removed outer cover which allowed access behind the control panel, was then able to take out the broken lever and with a little maneuvering was able to replace it with the new one. The whole process took less than an hour and was easy to accomplish.

It was really easy just unplugged it took off the back cover changed the part out put back cover on plugged it in and the elements were working great!