Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Cord was not tightened enough by delivery crew.
PF alarm appeared on display. Noticed clicking when cord was moved. Had arced for some time and melted original block. New part slightly different. Only has 3 lugs, old one had six. Stack using washers provided. Take note of colors before disassembly. Use caution while working through access opening. The edges are sharp. Only tools needed are phillips screwdriver, deep socket for lug nuts. Nut driver optional. Hope this is helpful.
Repair was quite easy, as long as you have the instructions for removing the door. The screws that hold the bottom of the door to the fixed hinge are placed into the side of the hinge assembly after removal; this holds the door at a 45 degree angle for easy removal. After that, just place the door on a flat surface and dismantle the door from the inside. The inner glass is contained in a metal frame with another piece of glass; this frame comes apart easily using the clips in each side. The door assembles easily after the glass is replaced; just take your time and give yourself enough room to lay out the parts as you go. Good luck!
Had to reference original owner's manual for instruction(s) on how to remove oven door. Used several "YouTube" videos to reference oven door design (Oven door glass is actually several layers of glass.) After completing about 30 mins of research and finding the right square drive bit, the repair went smoothly and without complications. The biggest challenge was researching and understanding what part(s) were needed and how to replace them. It seemed liked a lot of work doing the research however it sure beat a $350 repair bill. It cost me $90 and about 1 1/2 hours of total time. Oven works better than ever, thanks parts select for the part(s) and diagram(s) ...
Have a double wall oven and the top oven would not shut off or broiler part would stay on and burn tops of food. Since bottom oven was not having any issues felt like it could Not be control panel so decided to try the temp sensor. Since replacing oven has worked properly.
Both oven bake and broil elements lost power suddenly at the same time.
Installation of the temparature sensor, one of the technician recommended parts took no time, just two screws and a snap off/snap on part. It did not fix the problem. I then replaced the main control panel, which requires more work, but didn't solce the ussue either. I then replaced the thermal fuse, which wasn't mentioned by tech support, and required much more disassebly of the top panels of the stove, with still no fix to the problem. I am waiting to replace the thermostat heat sensor unit, the only other part in the circuit controlling power supply, requiring removal of the stove top again,
There is an installation video , but it was so easy, and if you clean your drip pans from those inevitable spills you can do this. I have zero mechanical abilities and I did. The website makes it easy to find your part, and the original literature you got with your appliance will direct you where to find the Model # and serial # on your Frigidaire Range. Order your part on line, get it in the mail and insert the Element yourself.Very happy with my transaction.
Oven wires arced and caused the terminal block to melt and become detached from the back of the range
Removed the wires that I could, then terminal block. Installing the new terminal block was very easy; however the wires that arced were fused to the terminal bock screws and needed to be cut and new connectors had to be put on the wires to allow them to be reattached to the block safely. Once all was replaced and reinstalled the oven has worked great. The length of the repair was increased because of the melted parts and having to run to the store to get the new wire connectors big enough to fit on the wires. If we were simply replacing the block and had not encountered the melted ends, it would have been a very quick and easy repair.
my original part arrived and it did not fit. When I called to explain the problem I was told it was the wrong part. The big problem is... Frigidaire calls the receptacle a terminal block kit as well as a terminal block kit which is a totally different part. I tried to explain that to several different folks I spoke to at your company as well as Frigidaire but I'm not sure if I got that point across. Take a look at part # 530 393 5058 and part # 530 440 9888 and you will see that they both mention terminal block kit. Hopefully the part I am getting from Frigidaire is an OEM part and will fit.
It was simple.............the range-top tilts up so I proped it with a stick of wood, pulled out the old burner and plugged in the new one (when I saw how inexpensive the new element was I orderd two to replace the other 8" because it didn't look long for this world either). The whole operation took less than 10 min. no tools or batteries required!!!!!!!!!.........no-mus-no -fus.
Your prices were the lowest I found on-line, keep up the great work!!!!!!!!!