This OEM 40 watt appliance light bulb is used for some ranges, refrigerators, freezers, and microwaves. Simply locate the existing bulb, unscrew it from its socket, and replace with new light bulb. If...
$19.73
In Stock
Order within the next 12 hrs and your part ships today!
The Frigidaire light bulb lens covers the interior light bulb in an oven. No tools are necessary to replace this item. After unplugging the appliance, slide off the wire bracket to remove the existing...
$10.90
In Stock
Order within the next 12 hrs and your part ships today!
This tempered glass is supplied by the original manufacturer and measures 20 inches by 13 inches. It is an inner door glass, designed for use in ranges/ovens and has several purposes which include pro...
$152.88
In Stock
Order within the next 12 hrs and your part ships today!
This OEM-manufactured metal temperature sensor, or oven probe, measures and regulates the temperature within the oven. If you find that your food is being overcooked, undercooked, or is not cooking ev...
$48.85
In Stock
Order within the next 12 hrs and your part ships today!
This part is the igniter/orifice mounting screw for your cooktop or range. It is approximately ½ an inch in length and is made of metal. The mounting screw connects the orifice to the cooktop. If the ...
$12.23
In Stock
Order within the next 12 hrs and your part ships today!
This OEM broiler pan and grate insert are cooking accessories used in your oven to broil food. The pan catches drippings and prevents them from falling into the appliance, while the grate insert ensur...
$68.24
In Stock
Order within the next 12 hrs and your part ships today!
The oven light socket allows you to screw in a light bulb so that you can see the inside of your oven. The light socket is located in the back of your oven, so you will need to remove the back panel t...
$46.58
In Stock
Order within the next 12 hrs and your part ships today!
This spark module or range spark module, is used in ranges and ovens. The spark module monitors and controls the spark to ignite the surface burner in a range. It does this by sending a certain amount...
$94.31
In Stock
Order within the next 12 hrs and your part ships today!
This flat glow bar igniter is designed for gas ovens. The function of the part is to ignite the gas to light the oven burner. If your gas igniter does not glow, or if it glows but will not light, you ...
$146.60
In Stock
Order within the next 12 hrs and your part ships today!
Questions And Answers for 79036903901
Be the first to ask our experts a question about this model!
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
Repair was quite easy, as long as you have the instructions for removing the door. The screws that hold the bottom of the door to the fixed hinge are placed into the side of the hinge assembly after removal; this holds the door at a 45 degree angle for easy removal. After that, just place the door on a flat surface and dismantle the door
... Read morefrom the inside. The inner glass is contained in a metal frame with another piece of glass; this frame comes apart easily using the clips in each side. The door assembles easily after the glass is replaced; just take your time and give yourself enough room to lay out the parts as you go. Good luck!
Turned power off at electrical panel. Pulled oven away from wall. Removed back cover (6 screws), then unplugged wires from old receptacle. I had to pull the squeeze clips backwards & break them to remove the old receptacle - couldn't squeeze them enough to remove them otherwise. The old receptacle came out through the inside of the oven,
... Read moreand the new one snapped in easily from inside the oven as well. Replaced wiring, installed new bulb, restored power & tested. Replaced back cover. Good time to vacuum under/behind where the oven usually lives before sliding it back to the wall.
The repair was nothing, but the diagnosis was a bit tricky. After carefully looking at the burner head, (cast aluminum) I pretty much figured out that the 4 small cast aluminum bumps that keep the burner cap positioned up in the air the correct amount to allow gas to flow under the cap, were worn down, preventing the gas from exiting pro
... Read moreperly by the igniter. My guess was correct. The new burner head solved all my problems. I love Parts Select for the ease of finding the correct parts and how fast they ship their orders. Great company, great service. Keep up the good work