The oven temperature sensor for your range may also be called a probe. The quick connect on this part may differ than your original piece. If the temperature sensor does not fit you will have to cut o...
$50.31
In Stock
Order within the next 11 hrs and your part ships today!
This tempered glass is supplied by the original manufacturer and measures 20 inches by 13 inches. It is an inner door glass, designed for use in ranges/ovens and has several purposes which include pro...
$152.88
In Stock
Order within the next 11 hrs and your part ships today!
This steel washer is also known as the range washer and is used on your oven door. The measurements for the steel washer are a three quarter inch outer diameter, and a one quarter inch inner diameter....
$11.23
In Stock
Order within the next 11 hrs and your part ships today!
This part is the igniter/orifice mounting screw for your cooktop or range. It is approximately ½ an inch in length and is made of metal. The mounting screw connects the orifice to the cooktop. If the ...
$12.23
In Stock
Order within the next 11 hrs and your part ships today!
This OEM broiler pan and grate insert are cooking accessories used in your oven to broil food. The pan catches drippings and prevents them from falling into the appliance, while the grate insert ensur...
$68.24
In Stock
Order within the next 11 hrs and your part ships today!
This kit includes 8 rubber feet and adhesive. This surface burner grate pad set is for ranges.
Surface burner grate pad set contains the four pads that attach to the bottom of the burner grate to p...
$72.95
In Stock
Order within the next 11 hrs and your part ships today!
This spark module or range spark module, is used in ranges and ovens. The spark module monitors and controls the spark to ignite the surface burner in a range. It does this by sending a certain amount...
$94.31
In Stock
Order within the next 11 hrs and your part ships today!
This flat glow bar igniter is designed for gas ovens. The function of the part is to ignite the gas to light the oven burner. If your gas igniter does not glow, or if it glows but will not light, you ...
$146.60
In Stock
Order within the next 11 hrs and your part ships today!
As per the factory, the original part was 19 3/4 inches and the new substituted part is 16 1/4 inches. According to the factory, this part will still work with your appliance.
$71.84
In Stock
Order within the next 11 hrs and your part ships today!
Questions And Answers for 79036719500
Be the first to ask our experts a question about this model!
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
Replaced clock control by removing surface burner control knobs and plastic nuts, and then the cover over the oven control. Two screw hold the clock in place, after removal and disconnecting the plug-in you can reinstall the new clock control. The Heat Sensor inside the oven will also need to be replaced. It is located inside the oven
... Read moreand attached with two screws; the back of the oven will need to be removed to unplug. Reverse removal procedure and turn the power back on to the stove.
Repair was quite easy, as long as you have the instructions for removing the door. The screws that hold the bottom of the door to the fixed hinge are placed into the side of the hinge assembly after removal; this holds the door at a 45 degree angle for easy removal. After that, just place the door on a flat surface and dismantle the door
... Read morefrom the inside. The inner glass is contained in a metal frame with another piece of glass; this frame comes apart easily using the clips in each side. The door assembles easily after the glass is replaced; just take your time and give yourself enough room to lay out the parts as you go. Good luck!
First, in order to easily access the oven door, I removed it by pulling straight out at the hinges. Then I removed the frame of the broken glass assembly by unscrewing the 2 screws at the bottom of the door and the 2 screws holding the door handle. I fit the new part in place, screwed the bottom 2 screws first, and then lined up the scr
... Read moreew holes in the assembly with the screw holes in the door handle and reattached the handle with the 2 other screws. IMPORTANT: ALWAYS USE A MANUAL SCREWDRIVER WHEN WORKING WITH THE GLASS ASSEMBLY...AND DO NOT TIGHTEN THE SCREWS FOR THE HANDLE TOO TIGHTLY (THE GLASS WILL SHATTER IF YOU DO!)
