Models > 72180043700 > Instructions

72180043700 Kenmore Range - Instructions

All installation instructions for 72180043700 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 72180043700
1-8 of 8
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

needed grease filters for a used over range microwave

  • Customer: tony from kewanna IN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 11 of 12 people found this instruction helpful
ordered on the part select web site, came quickly, order was correct

Microwave failed to head and light, fan, and turntable failed to come on.

  • Customer: Robert from Cedar Park TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Problem was due to a faulty door switch. Replaced with a new switch and the microwave now works fine! Only thing that was tricky was that LG uses the hex screws with a peg in the middle to keep the microwave cover on. Had to use a small screwdriver and pliers (on the screwdriver) to unscrew the screws.

suddenly stopped working while in use

  • Customer: Kevin from Colonia NJ
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
i unplugged the unit,unscrewed the outer shell so that all the wiring and internal components were visible.starting at the first of three micro switches i removed the slip on terminals installed the alligator clips too the wires so the switch would now be bypassed.i made sure the wires and clips were not touching anything plugged unit in and it worked.i then installed the new switch and closed up the outer shell

turn table motor

  • Customer: Gary from Desert Hot Springs CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
remove the screws from the bottom, leave tthe light wires attached. There are two screws holding the motor on, disconnect and mark the old unit where the yellow wire goes. Mount motor with two screws and connect wires. Turn on Miicrowave for 10 sec, to be sure all is correct. Attacch bottom cover and reattach power cord. Before doing anything make sure power cord is disconnected and reattached when sealed.

No Heat

  • Customer: Dennis from Chesapeake VA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
1. Removed unit from the cabinet. (2 screws). 2. Remove the outer microwave metal shell. (10 screws). 3. Locate and remove part. (3 screws). 4. Install new part and replace all screws. 5. Install unit back into cabinet. So easy. I will share this site with all of my friends.

Light bulb burned out

  • Customer: Craig from Burke VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I unscrewed the light cover, removed the burned out light bulb and replaced it with one I ordered on Partselect.com. It was very easy.

microwave turntable will not turn

  • Customer: LINDA from OCEAN CITY MD
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
removed screws from bottom of microwave... lowered bottom plate.. unplugged motor and replaced with new motor/AC synchronous. Reinstalled bottom plate......... DONE!!

Microwave would not heat food, but everything else worked.

  • Customer: Samuel from Daleville VA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Problem was a faulty door latch switch. I easily accessed the switch by removing the control panel, total of 4 screws. After that, just disconnected the three switch door latch assembly and connected the new one. Took about half an hour and was very easy. Unit works perfectly now.
All Instructions for the 72180043700
1-8 of 8