Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 70C

70C Maytag Dryer - Overview

Get Parts and Repair Help for 70C

If you know the dryer repair part you need, you can browse the list of all parts on the 70C, or you can search by name or part description. You can also find your part by where it is located on the 70C by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for 70C parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$11.88

Drum Roller Shaft Washer

If you notice that your dryer is noisy or will not tumble, then you may need to replace the drum roller shaft washer. This drum roller shaft washer is just under an inch in diamete...

$6.08

Rubber Foot Pad

The leveling leg pad or foot pad fits over the leveling leg on your washing machine. The foot pad is designed to protect your floor and keep the washing machine level and in place. This foot pad is just over an inch in diameter. It is made entirely of rubber and is gray in color. This pad is intended for use with washers and some dryers. Many of our customers have rated this repair as very easy. To complete the repair, turn the old leg counter clockwise to remove it. Then, simply remove the old pad and replace it with the new one. Finally, re-attach the leg by turning clockwise. Ensure that the washer is level, and adjust the leg accordingly if it is not.

$7.86

Adjustable Levelling Leg

If your washer shakes or vibrates loudly when it reaches its max speed, make sure the 4 levelling legs are even. Adjust the legs so that the machine is level, and tighten the locki...

$45.94

Round Carborundum Oven Igniter

This round style gas oven igniter, or also known as a broil or bake igniter, has an amperage range between 2.5 and 3.0. It glows white hot to ignite the gas for the oven. The igniter does this by attracting electrical currents through the safety valve to open it. *Please note: this does not replace the flat style igniters. If your gas igniter does not start, glows but does not light, or produces little to no heat when baking, replacing this part could be the solution to your problem. Refer to the diagram provided by the manufacturer for further instructions and guidance.

$4.63

Cylinder Light Bulb

Sold individually.

$54.12

Water Inlet Valve

This water inlet valve is intended for use with under counter style dishwashers. It has a 3/8 of an inch FPT (female pipe thread) valve and a mounting bracket. - This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the desired amount of water needed.

$30.36

Indicator Light Kit

$28.48

Dishwasher/Portable Washer Roller

$4.89

WASHER

Double Burner Assembly

This double burner design is not to be used with sealed burner style models.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The lower burner would not ignite.

  • Customer: Mark from Rego Park, NY
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 70 of 75 people found this instruction helpful
First I removed the oven racks. Then I loosened the two screws in the back of the oven floor and figured out how to remove it. Then I loosened the two screws at the front of the diverter and, with some pushing and pulling and twisting, was able to get that to come out, too. Then I tried lighting the oven and noticed that the igniter was not glowing. When... read more

Leaky water inlet valve

  • Customer: Jack from Fort Worth, TX
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Wrench set
  • 17 of 20 people found this instruction helpful
Easy. Removed screws at top holding dishwasher to counter. Turned off water to dishwasher. Unhooked water supply line. Electrical and waste lines were long enough to leave connected and pull dishwasher out, set on side. Pull off electrical connector. Use pliars to compress spring holding water line to dishwasher, remove that line from valve. Use nut d... read more

Stripped leveler screw making impossible to level my washer

  • Customer: Rebecca from Wylie, TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Wrench set
  • 17 of 22 people found this instruction helpful
Put blocks under the washer where the leveling leg was needed and screwed the part into the washer. Then it was just a matter of moving the washer into place and leveling. Pretty easy. read more