Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 6ALSQ8000MW3

6ALSQ8000MW3 Whirlpool Washer - Overview

Get Parts and Repair Help for 6ALSQ8000MW3

If you know the washer repair part you need, you can browse the list of all parts on the 6ALSQ8000MW3, or you can search by name or part description. You can also find your part by where it is located on the 6ALSQ8000MW3 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for 6ALSQ8000MW3 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$5.11

Agitator Directional Cogs

These agitator directional cogs are commonly referred to as dog ears. They come four to a package and are usually used with direct drive washing machines.

$25.37

Clutch Assembly

A worn clutch can cause a slower spin speed which will leave your clothes wet after a cycle. This clutch assembly comes with brake cam driver, blue spring for large capacity washers and black spring for compact washers. As per factory, the green spring (1.24") replaces the black spring (1.46").

$5.11

Thrust Spacer

This white thrust spacer is made of plastic and is also commonly referred to as a retainer ring. It is used in the agitator assembly of many direct drive washing machine models. Th...

$11.30

Tub Wear Pads - Package of 3

This package of pads contains three brown tub wear pads.

$29.40

Agitator Repair Kit

This six piece agitator repair kit comes with a four inch cam, a thrust spacer, and four dogs ears (agitator cogs). This kit is used to move the upper agitator and it connects the...

$7.60

Leveling Spring

This spring is used on the leveling components in a washer. Please note, this spring may differ in appearance, but functions the same as original.

$14.02

Suspension Pads - Package of 3

$7.20

Touch-Up Paint - White

18ml

$15.50

Tub-to-Pump Hose Kit

This kit comes with the clamps.

$29.30

Clutch Lining Kit

This kit comes with springs, hardware, and brake lining.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Replace Water Pump Coupling

  • Customer: RICHARD from PHILA, PA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set, Wrench set
  • 662 of 690 people found this instruction helpful
Removed casing tip over washer disconnected water pump. Disconnected motor then replace coupling then reassemble motor then replaced water pump. read more

washer wouldn't agitate

  • Customer: mike from Kent, WA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 607 of 627 people found this instruction helpful
First pry off the cap of the agitator. Then using a socket remove the bolt that holds the plastic cup in place. Remove this cup by prying it loose from the two tabs that hold it in place. Once this cup is removed you can get to the broken cogs.
Slip the new cogs into the underside of the cup, and slide the cup back down in the agitator housing usin... read more

Washer not agitating

  • Customer: Craig from Polk City, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 521 of 528 people found this instruction helpful
On top of the agitator is a flat cap that is held in place by the friction of an o-ring, there are no fasteners. I would imagine one could get under the lip with a small screwdriver or butter knife to pop it off but I chose simply using my fingernails so as to not disfigure the cap. Under the cap you will find the head of the only bolt that holds the assem... read more