Models > 6898VVV > Instructions

6898VVV Magic Chef Range - Instructions

All installation instructions for 6898VVV parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 6898VVV
16-30 of 332
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

bake element cracked

  • Customer: Ruth from Moyock NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 14 of 19 people found this instruction helpful
Being a woman, I first cleaned the oven. Removed two screws holding the element in place. Pulled element out about 3 inches and disconnected one clip attached to a yellow wire another clip attached to a green wire. Put new element in connected clips. Replaced screws.

The oven would not heat properly

  • Customer: Philip from Edgewood KY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 12 of 13 people found this instruction helpful
Pulled the oven away from the wall. Removed two screws inside the oven. Pulled old heating element out. When I did I heard a loud pop and and saw smoke. I assumed the element would not be electrically live if the oven was not on. That was obviously incorrect. I pulled the plug and then completed the installation. I went to chruch on Sunday and thanked God that I was not electrocuted. Now the oven works fine. My wife wanted the oven to die so that she could get a new alppliance, Instead I am alive.

Seriously your service was great. Your web site pointed me to the correct part, and it arrived the next day! I would definitely use your service again if I remember your name.

The oven stopped heating

  • Customer: GENE from TRENTON SC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 10 of 11 people found this instruction helpful
First I swiched off the circuit breaker just to be safe.Then I removed the two mounting screws and disconnected the the element leads. Very easy task, approx 5 mins. THANKS

Oven door wouldn't close or open all the way

  • Customer: Michael from St. Cloud MN
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 11 of 15 people found this instruction helpful
1st removed the sealed burners
2nd removed stove top
3rd removed oven door
4th removed left and right side pannels to access door hinges
5th removed left and right hinges
6th installed new left and right hinges
then re-installed other components in reverse order.
The oven door now opens and closes properly, the heat stays in the oven!!

defective oven sensor

  • Customer: sean from easthampton MA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 9 of 10 people found this instruction helpful
Checked online to see what F3 readout on stove meant. It meant replace sensor. Ordered part on a Sunday and part delivered Tuesday, Monday being MLK day. Detached bad sensor(2 screws inside oven)had to pull new sensor connector through hole from behind as insulation was too heavy (only removed 4 screws on right rear panel.Clipped wires together and reattached sensor inside oven. A cakewalk.

Oven wouldn't heat the right temperature (you would have to add 100 degrees on to it)

  • Customer: Claudine from Bethlehem PA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 8 of 8 people found this instruction helpful
Pulled oven out of the cabinet/wall and pulled sensor out and replaced with new one.

oven heating/bake element cracked

  • Customer: Carol from Brunswick OH
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 8 of 9 people found this instruction helpful
First-my daughter needed her pizza and I didn't want to even think about the cost of a new range. So she did some research online about replacement parts. Lo an behold, Partselect.com was our answer.

We received the part in a few days and replaced it with just unscrewing a few screws.. AFTER we unplugged the range. We also used a tool that I would describe as a nail remover/lifter to get the end off of the wire connection. Needless to say, we were rookies and had no experience with this type of repair and were so proud that we were able to spend less than $30.00 to fix our oven.
Thanks to Partselect.com for making it easy to do this repair on our own.

Code said we needed a sensor

  • Customer: Janice from Portland OR
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 8 of 9 people found this instruction helpful
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires to remove the old sensor. Went on line to find out where to order it from. Ordered it, It was on back order but was only about 1 week to receive. Reversed the procedure. WA LA. It works great.

1998 oven unit flashing F3

  • Customer: chris from houston TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 8 of 10 people found this instruction helpful
SHUT OFF BREAKER FOR OVEN! pulled oven out to get at backside,removed 3 screws on back coverplate,removed 2 screws inside oven at sensor in top left corner of oven,disconnected plastic clip at back ,pulled old sensor through hole.replaced sensor with new in reverse order. 15minutes tops.

Spring on hinge broke. Door wont close totally

  • Customer: Thomas from Baton Rouge LA
  • Difficulty: Very Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 7 of 7 people found this instruction helpful
Using the description on the first DIY, I did as told. All went well until the part about removing the panel to access the hinge. There isn't a "panel" on the side of this particular model of Magic Chef stove. You have to remove the entire side of the stove, and then, there's another panel inside of this one. That too has to come off. Once off, you're into the insulation surrounding the oven. Ain't pretty, I'll assure you. Then, the replacement hinge has holes in it for the mounting screws. The holes aren't threaded, and you have to replace the screws that come with the hinge with self-tapping screws. Either that, or thread the holes with a tap. Thank goodness my wife loves the stove, or it may have just gone out the door. This is not one of Magic Chefs better ideas. Either that, or they didn't plan on having to replace the hinge before the stove wore out.

Timer Controller (Clock & controls) not working/lighting up

  • Customer: S Gregory from New Braunfels TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 7 of 8 people found this instruction helpful
Simple. Just take off Ceran cook top, I used my iPhone to take a picture of the electronic relay board I was replacing just in case I need a reference picture. With circuit breaker turned off, I removed one connection at a time from the old board and plugged into new board (a total of 7 connections), popped the old board out, popped the new board in, no screw driver needed for this part--just for replacing the ground wire on the Ceran cook top. Reassembled top and flipped the breaker. Works like new!!

After self cleaning the oven received an error code telling me the sensor was bad.

  • Customer: Christine from Davie FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 7 of 9 people found this instruction helpful
Removed the two screws holding the element in place. I then pulled the element and wiring out until I saw the connecter. I disconnected the two wires and then chose the correct connector from the package, snapped it back into place, put the screws back, turned on the breaker then tested the oven and found that everything was working correctly.
This is the second time I have ordered from Part Select, the first time was for a front LED panel on the same appliance. With the help finding the part you need and the comments from other customers I have saved a lot of money by repairing these problems myself. Oh, and the best part is the look on my husband's face when he came home and found out the repairs were made by me and not a repairman that he said I should call. He said he would laugh when the first repair by me didn't work but who's laughing now : )

SMALL ELEMENT ON COUNTER TOP RANGE NOT HEATING.

  • Customer: Brian E from Waldorf MD
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 7 of 9 people found this instruction helpful
1. TURNED OFF POWER TO TROUBLE SHOOT THE COUNTER TOP RANGE ELEMENTS.
2.RAISED THE COUNTER TOP UP TO WORK ON IT AND SLID TWO EVENLY PLACED WOODEN SLATS UNDER THE BOTTOM OF THE HOUSFOR STABILITY SO IT WOULD NOT FALL BACKDOWN INTO THE COUNTER TOP CUT-OUT.
3. WITH A 1/4" NUT DRIVER REMOVED THE 10 HEX-HEAD SCREW THAT WERE HOLDING THE BLACK GLASS TOP IN PLACE, PULLED OFF THE 4 .CONTROL KNOBS AND CAREFULLY REMOVED THE GLASS COVER AND CAREFULLY SEET IT ASIDE IN A SAFE PLACE.
5. A VISUAL INSPECTION OF THE NON WORKING ELEMENT SHOWED THAT IT HAD A BURN OUT SPOT CAUSING IT NOT TO HEAT.
6. GOT THE MODEL NUMBER OF THE APPLIANCE AND CHECKED THE INTERNET FOR PARTS SUPPLIERS, CHOSE PARTS ELECT BECAUSE THEY HAD THE PART IN STOCK AND COULD OVERNIGHT IT FOR REINSTALLATION THE NEXT DAY, PART DID ARRIVE THE NEXT MORNING. A VISUAL INSPECTION SHOW THAT IT WAS THE CORRECT PART AND IT WOULD BE A LIKE FOR LIKE SWAP OUT.
7. PRIOR TO REPLACING THE ELEMENT CHECK TO SEE THAT THE ELECTRICAL POWER WAS STILL OFF AT THE CIRCUIT BREAKER, MADE A QUICK SKETCH OF THE WIRING AND IDENTIFIED THE WIRES SO THAT THEY WOULD BE RETERMINATED AT THE SAME POINTS.
8.USING THE NEEDLE NOSE PLIERS PULLED OFF THE 4 STAKE ON TERMINATIONS.
9. LIFTED OUT THE 6" FROM THE BODY OF THE UNIT , REMOVED THE 4 PHILLIPS SCREWS HOLDING PARTS WHAT WERE TO BE TRANSFERED ONTO THE NEW ELEMENT.
10. TRANSFERED PARTS ONTO THE NEW ELEMENT, REINSTALLED THE ELEMENT INTO THE BODY OF THE UNIT, REINSTALLED THE 4-STAKE-ON WIRES TO THERE APPROPRIATE TERMINALS AND VERIFIED WITH PREVIOUS WIRING SKETCH.
11. REINSTALLED THE GLASS TOP, 10 SCREW HOLDING IT IN PLACE AND THE 4-CONTROL KNOBS.
12 .TURNED MAIN POWER TO THE UNIT BACK ON AND TURNED ON THE REPLACED ELEMENT, IT WORK CORRECTLY, ALSO CHECKED THE OTHER 3 ELEMENTS TO MAKE SURE THAT THEY WERE WORKING CORRECTLY.
13. WHEN THE UNIT HAD COOLED, REMOVED THE WOODEN SLATS AND LOWERED THE COUNTER TOP BACK INTO ITS CUT-OUT MAKING SURE NOT TO DAMAGE THE GLASSTOP.
JOB COMPLETE.

Broken drawer glide

  • Customer: Peter J from Valparaiso IN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 6 of 6 people found this instruction helpful
As I pulled the drawer looking for a pan stored in bottom drawer the drawer glide broke. The pictures of the parts were fantastic. Not being sure of which of two parts from the photos, I ordered two parts knowing that hopefully one would be the correct one and the other would not be the part I needed. Parts arrived and it was clear which of the two parts would fit perfectly.

I screwed in the part, and that was it , and I was relieved that the problem was solved! I kind of feel lucky that your company is in business! The other part is fully accepted and plan to send it back in for a refund. And oh yes, I solved my appliance problem under $20.00 - unbelieveable these days!

Thank you again for beng there!

Inner Galls on door was craked

  • Customer: Randall from Katy TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 7 of 9 people found this instruction helpful
Remove outer panel first, outer glass and handle come off as one piece. Be carefull to secure as last screws are removed. Remove inner silver panel. Remove broken glass and replace with new. Reaassemble. Around 10 Phillips head screws altogether. Much easier than I thought
All Instructions for the 6898VVV
16-30 of 332