Models > 687WM-TKSAW

687WM-TKSAW Admiral Range - Overview

Get Parts and Repair Help for 687WM-TKSAW

If you know the range repair part you need, you can browse the list of all parts on the 687WM-TKSAW, or you can search by name or part description. You can also find your part by where it is located on the 687WM-TKSAW by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your range. We’ve also included any installation videos we have for 687WM-TKSAW parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

$2.52

Light Bulb - 40W

Sold individually.

$39.35

Flat Style Oven Igniter Kit

The flat style gas oven igniter included in this kit has a body length of 3-3/4 inches. This kit comes with all of the pieces you need to replace longer ceramic igniters, though this kit can also replace short igniters. This igniter has an amperage range of 3.3 - 3.6 and does NOT replace round style oven igniters.

$36.48

Sealed Burner Cap with Electrode

This burner cap assembly is sold with the spark electrode. Please note this part has been redesigned and no longer requires a gasket. Sold individually.

$28.56

Short Oven Sensor Kit

This temperature sensor detects the temperature within the oven cavity.

$24.70

Burner Head Cap with Spark Electrode

This is a black burner head with the spark electrode. NOTE: This part has been updated and there is no longer a gasket seal required.

$18.07

2 Piece Broiler Pan

$5.10

Oven Door Spring

Sold individually.

$6.20

Screw - sold individually

$3.82

SCREW

$2.70

Screw

This screw is sold individually.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Oven would not work but the Broiler did

  • Customer: James from Ferndale MI
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 161 of 174 people found this instruction helpful
The oven had been working intermittently for a while and after repeated threats of starvation from my spouse I finally took a look even though it was summer and the grill was working fine. The Igniter would glow red when the oven was turned on but the gas would not flow to it no matter what the temperature setting. I searched online and found this site that ... read more

A burner wouldn't spark strongly enough to light the gas.

  • Customer: Matthew from Brookfield MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 90 of 102 people found this instruction helpful
Replacement of these burners is very easy. You just twist the burner counterclockwise a quarter turn and pull it out. (You may need a big wrench if the range is very old.) Once out, just pull the two wires off and push them onto the new burner. Crimp them on with pliers if they're loose -- mine were. Twist the burner back on.
If the gasket under the bu... read more

F1 code - gas over would not heat.

  • Customer: george from birmingham AL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 73 of 81 people found this instruction helpful
Repair tech checked oven and said the control panel was bad and needed to be replaced. The new control panel would cost over $450.00! I found that the oven sensor was bad and replaced it for $30.00. The old oven sensor had failed following a self cleaning cycle. I found that the wires coming out of it were burnt.

Replacing the oven sensor was ... read more