Models > 666AJ ESVW > Instructions

666AJ-ESVW Admiral Range - Instructions

All installation instructions for 666AJ-ESVW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 666AJ-ESVW
1-15 of 40
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Inner Oven Glass broken

  • Customer: David from Wayne NJ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 18 of 23 people found this instruction helpful
I removed two retainer screws which released the outside panel.
Next I removed 2 screws which hold the middle glass pane from one of its retainer brackets.
The was another panel with 4 screws to remove before reaching the final glass inner assembly.
Once that panel was reoved with the broken glass it was time to put the repacement glass assembly back together.

replaced heating element on flat surface stove top

  • Customer: dennis from assonet MA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 16 of 23 people found this instruction helpful
I removed 4 screws and then lifted up the top it gave me access to the element I followed the direction that came with the element (very clear to follow) removed and installed the new element and it worked fine. Remember to unplug the stove if it is electric this is not in the instructions.

Element burned out

  • Customer: Anita from Hudson CO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 15 of 23 people found this instruction helpful
Unplug Stove removed screws pulled out
element. Lifted off the wires with a pliers they slid
onto the element ends that were pointed up
was very easy.

Burned terminal block and filter board

  • Customer: Joseph from Decatur GA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set, Wrench set
  • 24 of 50 people found this instruction helpful
Removed and replaced above named parts, rewired.Be sure to tighten all nuts that secure wires. I believe this is what caused the problem.

oven door spring broke and had to be replaced, oven light out and had to be replaced

  • Customer: Ed from Anderson IN
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 7 of 8 people found this instruction helpful
The old gasket fell apart as I replaced the oven light and had to be replaced. That was very easy once I received the part. The spring broke on the oven door and had to be replaced. I initially tried to reach in from inside the pan drawer under the oven. That was impossible to reaach but it only took a few minutes to realize that I had to remove the side panel. I had to slide the range out from between the cabinets, but once that was done it was a relatively easy fix, without any special tools needed.

spring broke on one side of door hinge

  • Customer: Travis from Lexington OK
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 6 of 7 people found this instruction helpful
Pulled the stove out, removed the sides and attatched the new springs( replaced both while the stove was out). Worked like new and put the stove back.

the left front burner burned out & none of the lights to show if a burner was hot would come on.

  • Customer: Richard from Fair oaks Ranch TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 5 of 5 people found this instruction helpful
FIrst we found the power source ( this took us awhile) and cut the power at the fuse box. then we unplugged the cooktop and started to take out screws. It turned out the screw removal had nothing to do with the stove top coming out. We took the taping knife & pried it under a corner and lifted. the cook top was just sitting on the counter.
The hardest part of the whole job was holding the cook top because we did not disconnect the downdraft fan other than to pull the tape off the vent & fan. Now we could undo the rachet screws that held the glass top to the cook top & remove it.
Theburner was simply a matter of pulling connections loose & placing them on to the new one. The clips that hold the burner in place were removed w/ a screwdriver & replaced on to the new burner. Watch for the numbers on the burner underside to know where to reattache the clips. the unit that lights up to show that a burner is hot would not come off, but we managed to remove
the plastic part even though the clip screw would not loosen, and since it only had to float near by we used the unused wire included in the new part to hold it in place. Putting the unit back together was not too hard, but it took us a little while to get it all lined up. Be carefull of what ever you work on, the downdraft fan scratched up the counter top that we were working on. we started with cardboard under it & should have continued, we did not want to try & remove the fan. Then we put it back in the counter opening & plugged everything back in & to our amazement ( we are not handy people) it worked! the lights that had refused to work when one unit was burned out now worked on all four units. thank you partselect, we were able to do the repair with what you sent.

replace light in oven

  • Customer: william from aiken SC
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 4 of 4 people found this instruction helpful
remove plate, gasket, & light cover then light. .Replace light. Put gasket on plate , insert cover. TAPE PLATE TO COVER ,then screw all in place, remove tape.

SMALL ELEMENT ON COUNTER TOP RANGE NOT HEATING.

  • Customer: Brian E from Waldorf MD
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 5 of 7 people found this instruction helpful
1. TURNED OFF POWER TO TROUBLE SHOOT THE COUNTER TOP RANGE ELEMENTS.
2.RAISED THE COUNTER TOP UP TO WORK ON IT AND SLID TWO EVENLY PLACED WOODEN SLATS UNDER THE BOTTOM OF THE HOUSFOR STABILITY SO IT WOULD NOT FALL BACKDOWN INTO THE COUNTER TOP CUT-OUT.
3. WITH A 1/4" NUT DRIVER REMOVED THE 10 HEX-HEAD SCREW THAT WERE HOLDING THE BLACK GLASS TOP IN PLACE, PULLED OFF THE 4 .CONTROL KNOBS AND CAREFULLY REMOVED THE GLASS COVER AND CAREFULLY SEET IT ASIDE IN A SAFE PLACE.
5. A VISUAL INSPECTION OF THE NON WORKING ELEMENT SHOWED THAT IT HAD A BURN OUT SPOT CAUSING IT NOT TO HEAT.
6. GOT THE MODEL NUMBER OF THE APPLIANCE AND CHECKED THE INTERNET FOR PARTS SUPPLIERS, CHOSE PARTS ELECT BECAUSE THEY HAD THE PART IN STOCK AND COULD OVERNIGHT IT FOR REINSTALLATION THE NEXT DAY, PART DID ARRIVE THE NEXT MORNING. A VISUAL INSPECTION SHOW THAT IT WAS THE CORRECT PART AND IT WOULD BE A LIKE FOR LIKE SWAP OUT.
7. PRIOR TO REPLACING THE ELEMENT CHECK TO SEE THAT THE ELECTRICAL POWER WAS STILL OFF AT THE CIRCUIT BREAKER, MADE A QUICK SKETCH OF THE WIRING AND IDENTIFIED THE WIRES SO THAT THEY WOULD BE RETERMINATED AT THE SAME POINTS.
8.USING THE NEEDLE NOSE PLIERS PULLED OFF THE 4 STAKE ON TERMINATIONS.
9. LIFTED OUT THE 6" FROM THE BODY OF THE UNIT , REMOVED THE 4 PHILLIPS SCREWS HOLDING PARTS WHAT WERE TO BE TRANSFERED ONTO THE NEW ELEMENT.
10. TRANSFERED PARTS ONTO THE NEW ELEMENT, REINSTALLED THE ELEMENT INTO THE BODY OF THE UNIT, REINSTALLED THE 4-STAKE-ON WIRES TO THERE APPROPRIATE TERMINALS AND VERIFIED WITH PREVIOUS WIRING SKETCH.
11. REINSTALLED THE GLASS TOP, 10 SCREW HOLDING IT IN PLACE AND THE 4-CONTROL KNOBS.
12 .TURNED MAIN POWER TO THE UNIT BACK ON AND TURNED ON THE REPLACED ELEMENT, IT WORK CORRECTLY, ALSO CHECKED THE OTHER 3 ELEMENTS TO MAKE SURE THAT THEY WERE WORKING CORRECTLY.
13. WHEN THE UNIT HAD COOLED, REMOVED THE WOODEN SLATS AND LOWERED THE COUNTER TOP BACK INTO ITS CUT-OUT MAKING SURE NOT TO DAMAGE THE GLASSTOP.
JOB COMPLETE.

Replacing the bulb in the freezer side

  • Customer: Yafa (and David) from Bothell WA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 4 of 5 people found this instruction helpful
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

oven light burnt out

  • Customer: William from Schwenksville PA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 5 people found this instruction helpful
1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes

Burned up oven door gasket needed replaced.

  • Customer: Daniel from Prescott MI
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Wrench(Adjustable)
  • 4 of 8 people found this instruction helpful
I started by removing the door, then trying to remove all of the screws in the oven casing. Of course the very middle screw in the bottom of the oven was rusted and dammged by use. I had to use a drill bit and remove the old screw. After dissasembly of the oven casing, I found that the lip that supports the gasket was rusted and burnt away about 3/4 in. I placed the new gasket in and found that when closed it covered this defect and sealed. I reassembled and cheked for operation.Ok! Imortant--remove the elements before removing oven casing.

Timer know would no longer set the time...

  • Customer: Rachael from Adams MA
  • Difficulty: Very Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers
  • 3 of 5 people found this instruction helpful
I removed the screws holding the bezel, removed the control panel frame, unhooked the four wires from the timer, and removed the timer. I cut the glue holding the circuit board into the frame and removed the circuit board. I unsoldered the faulty encoder switch, dissassembled the switch, determined the correct specifications for the switch, and ordered the nearest equivalent from an electronics supplier. I modified the new encoder to accept the shaft from the old encoder and I re-drilled the circuit board to fit the new encoder. I then soldered and wired the encoder, reversing the wires to correct the direction of rotation. I then reinstalled everything and added the knob purchased from partselect.com. Now it works. Tough repair - not for the faint of heart or those of average skill. But for the record, installing the knob was of course child's play and took only a moment.

Left front burner went out.

  • Customer: Donald from North Highlands CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 3 of 5 people found this instruction helpful
Removed 8 screws of retainer holding glass top to box.. Pulled 5 knobs and glass top and set aside. Popped 2 retaining clips holding burner , removed them and transferred to new burner (#12 and #48 position). Used wide blade screwdriver to facilitate removing terminals from old burner and attached terminals to new burner.Popped retaining clips into crossbeam, put glass top on and 8 screws back into retainer. Works great.

Replace clock-adjust knob

  • Customer: OSCAR from BRISTOL CT
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 2 people found this instruction helpful
Although normally a push fit, we drilled and tapped a #6-32 cross hole and used a set-screw to attach the small knob.

The original knob is still hiding somewhere but, thanks to PartSelect we are back in business !
All Instructions for the 666AJ-ESVW
1-15 of 40