Models > 66575775890 > Instructions

66575775890 Kenmore Range - Instructions

All installation instructions for 66575775890 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 66575775890
16-30 of 95
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The side trim was broken when I cleaned the door.

  • Customer: Ann from Whitewater WI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 8 of 14 people found this instruction helpful
The repair was easy. I had to remove the trim on the other side and the bottom. You slide the new trim on and screw in the bottom two screws.

I broke one side of the oven door trim while cleaning

  • Customer: Charles G from Apex NC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 8 of 14 people found this instruction helpful
I removed the bottom srtip. Installed the new bottom strip, snapped in the side pieces. [The old ones screwed in.] Replaced the original handle. Ready to reinstall door.

Gas Oven was not lighting

  • Customer: Edwin from Virginia Beach VA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench set
  • 6 of 8 people found this instruction helpful
After I found the web site I looked at the possible solutions for my problem. My igniter was glowing so I was not sure that would fix the problem but several places indicated the igniter would fix the problem and after I replaced it the oven work great.

Didnt keep Left/Right trim in their box - parts had no ID on them.

  • Customer: Michael from Valencia CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 7 of 12 people found this instruction helpful
PS733869 Door Trim Kit - Since I was replacing broken and discarded trim parts and had taken the replacements out of their identifying boxes I had some unneccessary difficulty since the parts are not marked. Point to reference is that the 9/16 side of the trim goes on the OUTSIDE EDGE of the door and the glass and handle are attached AFTER the trim is installed. Glass goes OVER the trim and not held in by it, the handle and the lower bracket does that.

missing screws for oven door

  • Customer: donna from baltimore MD
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 5 of 6 people found this instruction helpful
After searching on the internet for a very long time, we were almost ready to order the screws "blind" (no picture) from Sears for almost $10.oo per screw. Then I stumbled onto this website and found exactly what I was looking for, with a detailed description AND a picture!! Not to mention a price that was two thirds less than Sears..for TWO screws. Now the oven door is secure and we are no longer on our search for the right screws.

Oven light not working

  • Customer: Carol from Allison Park PA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 7 of 12 people found this instruction helpful
I turned off the breaker (I'm a little nervous even unplugging a 220 plug). I first removed the cover from the back of the stove to get to the wiring/socket. Removed the two wires from the leads - they just pull off by hand but use a needlenose pilers if it is stuck. One is larger so no need to try to remember which one goes where. I removed the glass cover and bulb from inside the oven. I read another post on this site that said there were clips that you had to press to get the old socket out which helped. That part was a little tricky as the insulation around the socket makes it hard to see and the opening is really tight. I finally found the clips and pressed one then got that side out enough to hold the clip back then pressed the other clip and I was able to push it right out. I did not have the strength to press both clips with enough pressure but if you do, that would probably be easier. From inside the oven, I pushed the new socket through the hole - there was a little notch in the opening that had to match up with the socket. I had to push pretty firmly until I felt both clips snap in place. Replaced the wires, turned on the power, screwed in the bulb and cover and I had light!

Igntr would glow but Oven wouldent heat

  • Customer: Elmer from New Baden IL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 5 of 6 people found this instruction helpful
I removed the two screws that held the igntr in place. Then I pulled the igntr out and unplugged the wires. Replaced the igntr with the two screws and plugged the wires back together. I then turned the oven on to 400 degrees and it heated like a new one.

scratches and paint detoriation on bottom part of oven

  • Customer: Peter from Galloway NJ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 4 of 4 people found this instruction helpful
Remove 2 screws holding oven bottom in place.Lift out the plate and replace with new plate. The hardest part of the replacement was lining up the screw holes. By the way i have never received such great service from any internet company as Part Select. I ordered the part on a Monday and the part was at my home the NEXT DAY and installed that evening.

Replacement of oven glass door

  • Customer: Jeanie from Anchorage AK
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 12 of 28 people found this instruction helpful
Parts arrived extremely quickly. Easy assembly. Would highly recommend partselect.com. Thank you.

Broke glass door on stove while cleaning it

  • Customer: Aires from Canton GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 7 of 14 people found this instruction helpful
I'm still unsure why it broke ,but it was just a matter of removing two screws that hold the handle in place and sliding in the glass...

oven light flashing off and on when door closed

  • Customer: Keith from Marion KS
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 5 of 8 people found this instruction helpful
removed the two screws that held the cook top on and moved it enough to get to the light switch. Removed the switch and tested with multimeter. Pulled the two wires out of the mounting hole and insulated with elect. tape. Replaced the cook top and installed the two screws that hold it in place. Located the switch at PartSelect on line and ordered it. When the switch came in (the next day), I connected the two wires, and snapped the switch in place, and I was back in business.

Oven wouldn't heat

  • Customer: Lori from Wimberley TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 4 of 5 people found this instruction helpful
I didn't do it, but I suggest putting down newspaper to keep from having to clean up all the charred remains that will inevitably fall from the parts you have to remove. First, unplug the thing so you don't shock yourself. I removed all the racks for easy access to the drip pan, which had to be removed by unscrewing two screws. Then there was a cover over the flame area that also required two screws being removed. The coil had two screws connecting it, but first I had to pull out the drawer at the bottom, crawl under the unit and unplug the coil. I removed the two screws from the old coil and replaced it with the new one, but first I had to get back under and plug in the new coil. I was unprepared for the virtual small animals that were under the stove, so I took some time to clean out that mess. I tested the thing to make sure it would work, and it did. I put all the pieces back in reverse order and had some really good baked chicken for dinner. I also recommend using gloves, as all the soot is hell on your nice manicure.

Outer glass of the oven door is broken.

  • Customer: Ernestine from baltimore MD
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 6 of 12 people found this instruction helpful
I took out the two screws that held the oven handle in place inserted the glass in the door and replaced the two screw!!! That easy!

broken trim

  • Customer: michael from Reynoldsburg OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 4 of 7 people found this instruction helpful
remove the hinge stays they just clip in
remove the door. took out screw at bottom of door.
replaced trim.
replacing the door was a problem i didn't have pins to put in the spring loaded hinges so i used nails to hold hinge in position.
so make sure to open oven door first insert pins or nails in hinges then remove door. It would have took 10 min. to do.

Both hinges were bent, probably from dropping the door, or leaning on it when it was in the down position.

  • Customer: Earle from Taylorsville UT
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 4 of 7 people found this instruction helpful
1st; I opened the door, 2nd; removed the keepers that prevent the door from coming unhinged. 3rd; placed 2 short screws in the holes in the hinges. 4th; raised the door until it stopped. 5th; lifted the door upward and slid the hinges out of the slots in the range. 6th; laid the door face up on a microwave stand. With a handle on the outside, and hinges sticking out of the inside, it was inpossible to lay the door flat on a larger surface, and get around it. 7th; removed 2 screws from the inside top, and the 8 screws from the very bottom. 8th; removed the bottom rail, and the handle assembly. From there everything was stacked pieces. Picked the glass front up, and carefully set it safely aside. Picked each piece up and cleaned it, and started the re-assembly. The hardest part of the process was getting the fiberglass rope around the inside glass, to stay in place during the initial re-assembly. From there, the assembly was just the reverse order. the process was about 1 hour and 20 minutes, due to lack instructions and practice, plus cleaning, finding screws, and tools, Instructions may have been on line, but I didn't find them. The new hinges came with pins in place, and should have come with an extra set to lock the old hinges.
All Instructions for the 66575775890
16-30 of 95