66568601891 Kenmore Microwave - Instructions

Simply removed two screws to remove the old vent grille and replaced it with the new grille. I was also very pleased with the assistance I received from the service rep. I had ordered the wrong grille. I called the PartSelect help number and the rep walked me through the product return process, then found the correct part and ordered it. I had the replace 3 - 4 days later. The rep was very polite and patient during the whole process.

Looked up the Whirlpool Co. and ordered the part. It was quite simple. Arrived in 2 days and I simply placed it in the microware. It was very very easy!

E. Robinson

easy to replace, just the same as cleaning the turntable and placing back in the micorwave;

Unplug appliance. Remove total of 7 phillips screws from sides and front of bottom panel . Panel front drops down, remove one socket screw and socket. Now have access for lineman' s pliers to unscrew bulb base. Reinstall socket, replace bulb and 7 panel screws. Restore power.

Took 4 Screw on top off...set bottom in first into slots ..pushed top in under the top of outside cover ...put Scews back in.

It took me time to remove the parts and suss out the issue, but the repair itself was EASY. A wire ribbon connected to the circuit board had gone bad. One Phillips head screwdriver, 7 screws, to get at the old one, pull it out, replace it with the newly ordered part. NO PROBLEM. Ladies, you can do IT!! You have the power!

Removed one screw lowered glass cover removed burned out bulb replaced with new one put glass back reinstalled screw. Dune 5 minutes back in business

Ordered a new motor. Removed the outside trim of the oven-microwave combo. 2 screws at the bottom of the trim. Removed the screws that held the combination micro and oven unit in place. Removed the top and bottom black plastic grill of the microwave. 3 screws each. Pulled the entire unit out about 1 inch exposing the screws at each side of the microwave that hold it in place.
Snapped off the top control panel which exposed the wiring connecting the control panel.
Unplugged a couple of wire harness units to free the control panel.
Be sure to label the units to know which goes where during reassembly.
Remove the microwave unit from the housing and place it on its side.
Remove the metal plate that houses the motor. 4 screws hold the motor in place. Disconnect the 2 wires from the old motor and you are ready to install the new motor. Be sure to TURN OFF THE POWER to the unit at the breaker box and remove the turntable from inside the microwave.

First, we had to clean up all the interior surfaces, which was just cleaning. There was no internal damage. Then, just setting the center connector, rotary rollers and glass plate. Simple

Took out turntable and swapped out old one with a new bright and shiny
New one, ring that is. It was easy using the part from parts select
Thanks
Paul

Unscrewed 4 different screws, replaced the vent & returned screws. Ack to original positions

Slipped in and screwed top on

Didn't realize this part had two tabs with reinforced screwholes in it. Those obviously had snapped off at some time in the distant past, and I had always removed the grille for cleaning carefully and washed it by hand and replaced it. The clean freak moved in and took this out WEEKLY and all the other tabs were eventually cracked and made the grille unusable; it kept rattling and falling out. When I got the replacement I noticed the broken tabs and replaced the item in a few minutes after removing the debris of five or six tabs and finding a Philips head screwdriver for the apparent screws (in fine shape, they were!) and tab remnants. Good fit, looks like new. Now hopefully the clean freak won't find my screwdriver next week.

Whirlpool Model# MH1150XMS-0 purchased in 2004. I called Whirlpool and they suggested a new microwave. No big surprise - being the thrifty person that I am I wasn’t taking this for an answer. I figured if I had to purchase a new microwave what was $35.22 (part# PS373828 + shipping) if it worked.

I replaced the latch on the microwave door. Once the latch was replaced. I also took this time to make sure that the microwave door was in alignment. Thereafter, I had to adjust the door interlock switch behind the microwave console panel to recognize the microwave being closed. Yes, gaining access to all these areas was a bit difficult but have patience. TADA!!!....microwave is working. #girlsrock

Removed bed two screw replace grill