Models > 66561709100 > Instructions

66561709100 Kenmore Microwave - Instructions

All installation instructions for 66561709100 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the microwave repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 66561709100
76-90 of 153
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Vent grill wouldn't stay on. The clips broke.

  • Customer: Julia from Baltimore MD
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Take out the screws, broken pieces of clip, then put in the new vent grill, replace the screws. Done!

Grill was cracked (mounting tabs) some time ago by unknown source. Suggest during in warranty problem on fire hazard. Vent grill was falling off.

  • Customer: John from Mentor OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Unscrewed the remaining (2) screws that held the vent in place, placed the new grill in the tab loctators, and screwed it into place. Done...in less than 10 minutes. It took me 15 minutes to find my wife to show her what a nice job I did.

part of grill plastic became crystalized and cracked

  • Customer: Judy from Albany OR
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
First, the screws were removed that held the vent grill to take off grill. The new vent grill was then replaced in a very short time. No problems at all.

Broken Vent Grill

  • Customer: STEPHEN from RICHMOND VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
I removed the 2 screws holding the broken vent grill, placed the new one in place and put the 2 screws back in place. Took less than 5 minutes from opening package to replacing the grill.

vent grille was knocked loosesomehow. allthe holes for the screws were broken

  • Customer: Benita from Port Orange FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Removed the screws from the damaged sections and replaced the new vent grille. Less than 5 minute fix, and saved me over a 100 dollars according to the quote I got. Thanks

Plastic vent on microwave was cracked and would no longer stay on.

  • Customer: Shirley from Coconut Creek FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Removed the broken parts and screws and placed the new vent on and tightened screws. I am an 76 year old woman, so if I could do this, then anyone can! Surprisingly easy to install.

Microwave gill fasteners broke and would not stay in place.

  • Customer: Karolette from Virginia Beach VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Replaced grill and greese and charcoal filters.

vent grill broken at installation screw

  • Customer: Tim from Palm Harbor FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
old vent off screwed new in less than a minute

Thought filters should be changed after 5 years of use.

  • Customer: Chris from Boulder CO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Used hands to slide filters sideways, till they could be pried out with screwdriver or bare hands. When new parts arrived, easily slide new filters into position. In hindsight, we did not need to replace grease filter. I was able to clean one of those with ordinary dish soap, warm water, and a brush.

BURNT OUT LIGHT BULB REPLACEMENT

  • Customer: alfred from summerville SC
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 6 of 19 people found this instruction helpful
OPEN COMPARTMENT, INSTALLED BULB, CLOSED COMPARTMENT

Plastic tabs broke and the grille fell off.

  • Customer: DIANA from BORDEN IN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Removed the screws holding the broken tabs and thought the new vent grille would click right into place. I had quite a bit of trouble getting all the tabs lined up to click into place, but was finally able to do it. Then I just used the old screws to secure the new grille.

The vent grille became lose and was falling off from the position each time we open the microwave.

  • Customer: Gloria from Middletown DE
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
First, I ordered the part.The part was sent to me within 2 days.Then,I removed the old one that was always falling off and mounted the new one. It was a perfect fit.

microwave vent grill

  • Customer: WALLEN from Anchorage AK
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
I have been doing repair on things on my own for years, I am a retired prevenative maintenace supervisor.
While cleaning the microwave vent grill from being old it fell apart, so I ordered the part using the internet to find the a company that has the same part, the part didnt take long before I recieved it. It didnt take five minutes to install it, and it saved me cash in the pocket from someone else to do the work. wallen

Vent grill plastic parts broke off so it would fall off the mircrowave

  • Customer: Emma from Alexandria VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Took screws off of old vent grille and installed new one. Very easy except my old one was a shiny black grille and this one has a matte finish. Description did not say which but I am fine with the part.

Vent was Broken.

  • Customer: Tom from Missoula MT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
I, carefully, inserted the bottom tabs into the appropriate slots. I then rotated the vent piece up and into place under the top lip of the Microwave. Once positioned I installed the screws required to hold the piece in place. Very simple replacement. It gave me a chance to clean the grease behind the vent.
All Instructions for the 66561709100
76-90 of 153