Models > 651AH > Instructions

651AH Admiral Range - Instructions

All installation instructions for 651AH parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 651AH
46-60 of 87
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The burner was shortening out and would work sometime. The first time I replace the burner but the new one shorted out quickly.

  • Customer: shawn from Vancouver WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 2 people found this instruction helpful
I unplugged the stove. Took out the burner and removed receptacle by pulling it out of the bracket and clipping the wires. One thing you want to make sure is that when you clip the wires from the receptacle you're replacing you leave enough wire so that you can connect them to the wires on the new receptacle when it is in place on the stove. I had just enough but would have liked more. The bracket I received didn't match the one on the stove so I used the one on the stove since the receptacle itself was the same as the one I was replacing.

Old surface element burned out.

  • Customer: Royce from Rio Rancho NM
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 2 people found this instruction helpful
I ordered and received the replacement element, then unplugged the old one and plugged in the new one.

Job done.

thermostat temprature bulb hanger clips

  • Customer: Dwayne from Atlanta GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 3 people found this instruction helpful
snaped them into oven cavity attached temp bulb job complete

burner not operating or intermittently

  • Customer: Elroy from Atwater MN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Shut off power at breaker box. Removed top burner unit. Removed old receptacle (Mounting screw was rusty so I drilld out the old one.) Cut wires from old unit. Stripped wires back on old unit. Attached old and new wire with ceramic wire nut. Attached new unit. Reinserted top unit. Reconnected power and "voila". Wife was smiling again.

Burner did not heat, but element is ok.

  • Customer: Philip from Hull MA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
The Burner Control Switch - 250V Part Number: PS2089409 that this site recommended was the right part for this older range. Had to remove screws to pull out the front panel with knobs, but it only pulls out a couple inches due to wires so it is tight to remove old switch. The five tabs are not in same spot so go by the labels and the wire lugs fit just fine, and the knob snapped right on and works great. Thank You!

needed a new drip bowl and couldn't find ons that fit exactly but you had it

  • Customer: Elsie from Garner NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I removed the old one and put in the new one. Works great!!!!!!!!!!!!

Burner receptacle had malfunctioned and been removed

  • Customer: Kerry from Silverado CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
10 Minutes for a stove my landlord thought was not fixable (repairman had already cut the wires to the element and capped them)! The delivery person handed me the package, I got out the single tool needed, installed the part, put away the tool, cleaned my hands, and put a pot of water on the stove to boil for pasta. 10 minutes!

Electric surface burner would only turn very hot

  • Customer: Vittorio from Wakefield MA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Well, I had to search a bit deeper in the internet to find out that the problem was not with the surface burner (which did look a bit burned out anyway) but rather with the surface burner switch (Part Number: PS336885) which must have ben damaged by the heat of the closest burner. If this problem would have been better documented (or if I would have searched more carefully) I would have saved over $40 with parts (Surface Burner Receptacle Kit) that I didn't quite need. Repairing the switch was very easy, thanks also to the available video , even though the stove used on this video (front panel) didn't quite match mine (top-back panel).

TO OLD NEEDED TO BE REPLACE

  • Customer: ROSARIO from MESQUITE TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
ACTUALY I JUST REMOVED THE OLD ONES AND REPLACE THEM WITH THE NEW ONES . AND THANK YOU FOR YOUR PROMPT DELIVERY I FOUND SOME ONE I CAN TRUST .THANKS AGAIN .MRS BOLANOS

rusty pans

  • Customer: Stewart from Hanover PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
simply remove the old and install the new; perfit fit

I needed to replace my burner pans.

  • Customer: Robert from Wilton CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
The Drip Pans are a cinch to replace with no tools necessary. The best part is that the Web Site is extremely easy to use, and the parts arrived two days after being ordered.

one pole of the socket corroded to nothing

  • Customer: martien from williamstown MA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Starting by me making a substitute prong to keep the stove working while the part this coming by mail. was a piece of cake.

Receptacle was no longer making good contact.

  • Customer: Fred from Edwardsville IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
This worked out GREAT. We were about to purchase a new range when I found the needed parts were available. The stores we had contacted had told us our range was too old to have parts available. I had no problem with installing the receptacle at all. The pans went in easly as excepted. My wife is happy with her NEW arrangement. She does not need to learn how to operate a new range. Thanks for your help. The instructions sent were clear and easy to follow.

drip pan were burnt out

  • Customer: Delroy from Miramar FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
simply remove the burner take out the drip pan and bowl individually. Install the new one and replace the burner. no tool was used.

Easy installation

  • Customer: Jeremie from Freeland WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Unplug stove from outlet!! Removed screws (Phillips head) from prior element and pulled out enough to slip of the red and white wires. Keep in mind which side which is on and take old element out of oven. Put new element in and attach wires back on the same sides. Push back in and use screwdriver (Phillips head) to lift insulation to push wires and element prongs back. Put screws back in, close oven door and plug stove back in. Tested and works great!
All Instructions for the 651AH
46-60 of 87