Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 61W

61W Maytag Washer Dryer Combo - Overview

Get Parts and Repair Help for 61W

If you know the washer dryer combo repair part you need, you can browse the list of all parts on the 61W, or you can search by name or part description. You can also find your part by where it is located on the 61W by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer dryer combo. We’ve also included any installation videos we have for 61W parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$3.02

Spring, Lid

The dishwasher lid spring helps open the dispenser cover in the soap box when the control releases the latch. If your dishwasher does not dispense detergent, is broken and worn out...

$6.08

Rubber Foot Pad

The leveling leg pad or foot pad fits over the leveling leg on your washing machine. The foot pad is designed to protect your floor and keep the washing machine level and in place. This foot pad is just over an inch in diameter. It is made entirely of rubber and is gray in color. This pad is intended for use with washers and some dryers. Many of our customers have rated this repair as very easy. To complete the repair, turn the old leg counter clockwise to remove it. Then, simply remove the old pad and replace it with the new one. Finally, re-attach the leg by turning clockwise. Ensure that the washer is level, and adjust the leg accordingly if it is not.

$7.86

Adjustable Levelling Leg

If your washer shakes or vibrates loudly when it reaches its max speed, make sure the 4 levelling legs are even. Adjust the legs so that the machine is level, and tighten the locki...

$5.51

Hose Clamp

The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installation, you will need a flat head screw driver to replace the clamp and a drill to access the screws to remove the front of the washer. Be careful if you do not have specific clamp pliers as the clamp could fly off. Once the front of the washer has been removed, take a quick look for water damage or any obvious signs of where the leak is coming from. If it is not obvious, run water to test.

$24.82

Detergent Dispenser Cover Kit

This kit also includes the lid hinge pin, spring, snap and latch.

$5.77

Screen

Found on the water inlet valve.

$4.48

Inlet Hose Washer

This inlet hose washer, also known as a high pressure inlet hose washer, is used in washing machines, refrigerators, freezers, and dishwashers. The function of this part is to crea...

$11.46

Spray Paint - 12 oz. - White

Appliance spray paint is a great way to cover up any chips and scratches that have appeared on your appliances. Instead of replacing the part entirely, this is an easy fix. This is also a great way to give a fresh new look to any handles or areas that have discoloring due to wear. Make sure to clean the area before you begin and wear a protective mask for safety. Give the can a good shake and spray a few inches away from the surface. Apply the paint until the area is fully covered as desired. Wait until the paint has dried before using the appliance.

$5.92

Hose Washer and Screen Insert Kit

The hose washer in this washer and screen insert kit is an inch in diameter. The insert is all blue in color and is made entirely of plastic, while the washer is all black in color...

$4.63

Cylinder Light Bulb

Sold individually.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Stripped leveler screw making impossible to level my washer

  • Customer: Rebecca from Wylie, TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Wrench set
  • 17 of 22 people found this instruction helpful
Put blocks under the washer where the leveling leg was needed and screwed the part into the washer. Then it was just a matter of moving the washer into place and leveling. Pretty easy. read more

The dispenser door would not open due to a broken spring

  • Customer: LARA from Murfreesboro, TN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 32 of 70 people found this instruction helpful
Removed the existing dispenser door, took off old spring. Slid new springs on pin, got it situated between the correct parts of the door. Popped it back on the pin inserts. Twisted spring into springing action position, voila. It was repaired. No repairmen. No additional costs, fees, nor extra time waiting on repairmen. read more

Both outside door handles turned very beige

  • Customer: Howard from Boynton Beach, FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 11 of 24 people found this instruction helpful
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles.... read more