Models > 60W > Instructions

60W Maytag Dryer - Instructions

All installation instructions for 60W parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 60W
1-15 of 57
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Baking element in oven exploded

  • Customer: Chad from Bloomington MN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 15 of 17 people found this instruction helpful
Removed the broken element by taking out the two screws in the back wall of the oven and unplugging the wires. Then did reverse to install the new element. Very simple repair job.

The dispenser door would not open due to a broken spring

  • Customer: LARA from Murfreesboro TN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 18 of 36 people found this instruction helpful
Removed the existing dispenser door, took off old spring. Slid new springs on pin, got it situated between the correct parts of the door. Popped it back on the pin inserts. Twisted spring into springing action position, voila. It was repaired. No repairmen. No additional costs, fees, nor extra time waiting on repairmen.

Stripped leveler screw making impossible to level my washer

  • Customer: Rebecca from Wylie TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Wrench set
  • 7 of 10 people found this instruction helpful
Put blocks under the washer where the leveling leg was needed and screwed the part into the washer. Then it was just a matter of moving the washer into place and leveling. Pretty easy.

Bake Element Was Burned Out

  • Customer: Scott from Fort Lauderdale FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 6 of 7 people found this instruction helpful
Turned the circuit breaker off. Removed the 2 screws holding the element in place, pulled the element out far enough to access and disconnect the wires. Installed the new element by reversing the process. Success - wife is happily baking again!

heating element

  • Customer: Virginia from Groton CT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 3 people found this instruction helpful
This was amazing. First I couldn't believe I could find a part for an over that was 25 years old. Fixing it was just as easy. I read some of the other reviews and it was just as easy as they described. Unscrewed the two plates on the back of the oven, unclipped two pieces and screwed the plates back on. It took me a total of 10-15 minutes, BUT, I couldn't get the door back on. Had to impose on a neighbor to help. Ten minutes to fix the oven and three days to get the door back on! Still worth it. THANK YOU THANK YOU THANK YOU

Bottom heating element had burned out.

  • Customer: Randy from Flagstaff AZ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 3 of 3 people found this instruction helpful
turned off the breaker (240 volts and it was outside, so it took longer than 15 minutes). Removed two screws in the back of the oven, one on each side of the old element, and pulled the old element forward. The wires on the back add some resistance, but they are long enough to pull forward a short distance (3 inches) without damage. Unplugged the old element, plugged in the new element, pushed it into place, and reinstalled the screws. Turned the power back on and it worked! Saved some money for the holidays! DIY para vida!

heating elements burned out

  • Customer: Billy from Corpus Chrsiti TX
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 2 of 2 people found this instruction helpful
it was really easy. The most time consuming is removing an replacing the unit from the built-in cabinet.

Burnt out element

  • Customer: Robert from Jacksonville FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 2 of 2 people found this instruction helpful
Recieved the part within 24 hrs after I ordered it which was awesome.
Removed the two screws holding element in place and pulled out to remove old element. Disconnected the wires and removed element. Had to replace the wire ends with slip on ends to match new element. Spent more time at Home Depot looking for $.99 ends and a crimper than it did to do the entire replacement. Reinstalled element with no problem. Worked great.

The original unit burned through and would not work, of course .

  • Customer: Wesley from Guymon OK
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 2 people found this instruction helpful
After unpacking and checking the unit that was mailed to me, I cleaned the ends of both the connections in the oven and the connections on the part, then plugged them together and screwed the plates in place in the oven. The oven worked immediately and still is working very efficiently. I had no problems at all with the installation.

Baking element burned out

  • Customer: Lana from Colorado City TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
Took two screws out of burned out unit. Pulled element forward and pulled off connectors. Replaced new element on connectors and screwed back in. Extremely simple. Less than 10 minutes.

the bake element was burned into.

  • Customer: Jerry from Big Stone Gap VA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 1 of 1 people found this instruction helpful
1. remove 2 screws holding element in place
2. unscrew the wires from the old element
3. the connectors on the new element was different from the old one
4. cut old connectors from wires
5. prepare wires for new connectors
6. install new connectors
7. connect the new element to the wires
8. replace the 2 screws removed in step 1
9. test the repair
10 it worked great.

Replaced baking element

  • Customer: Chris from Owatonna MN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 1 of 1 people found this instruction helpful
First, I removed the 2 screws holding the element in place. Next, I pulled the element out abotu 4 inches and disconnected the wires attached to the element. I was able to do one by hand, but the other required needle nosed pliers. (be careful not to pinch the connecting wire). Then I attached the wires to the new element. Lastly, I replaced the 2 screws to hold the new element in place.

Old unit was broken.

  • Customer: Wade from Sun City CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 1 of 1 people found this instruction helpful
My son is very handy. He had no trouble installing the new heating unit. The new part seems to be working well.

burned out element

  • Customer: David from Martinsville VA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
removed old burned out element, installed new element

Element burnt out

  • Customer: Paul from Seattle WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
I killed the circuit breaker to the oven, then double checked with an electrical tester. I removed the oven door for easy access, unscrewed the element bracket screws, plugged in the new element and then I reversed the steps above.

I am very happy with PartSelect and will use them in the future for all my appliance parts needs.
All Instructions for the 60W
1-15 of 57