5KSM150PSBPK4 KitchenAid Mixer - Instructions

Watch U Tube video. Take care to keep track of disassembly. Hard part was to have 4 types of screw drivers to fit the different screw heads. Be sure to clean broken gear clogs out of the grease. Parts select lady was a great help. Download Parts select diagram for extra help. Time and patience!

Removed old plate, screwed in new plate and works like new! Was so happy I wouldn’t have to replace my 30 year old mixer.

The new part was too large for the replacement job, but we used the self tapping screws that came with the mixer and screwed them in from the bottom to open the holes a little more since the original screws were to short to hold the new plate. Then we replaced the screws with longer screws and that seemed to do the trick!

The brushes are located on each side of the tilt head of the mixer. I used a screwdriver to remove the screws, removed the brushes & replaced with the new ones. Runs great again!!

Skewer the screw in with my fingers,

Dismantled the mixer, took photos, and re-assembled unit.

With a screw driver remove the screws holding the old base in place. With a flat head screw driver carefully pry and remove old mixer base. With 600 grit sandpaper clean and make smooth any burrs or rough spots in the mixer base recessed area. You can use some light grease and coat the outer edges of new mixer base and place in the now cleaned mixer base recessed area. The new base maybe a tight fit and not be fully seated in the recess. If a tight fit, place the piece of 2x4 piece of wood over the new part that is in the recess and carefully tap the base home using the sledge hammer. Check to see, if the base is fully seated. If not fully seated, tap again When fully seated replace the screws. You may have to adjust the height of the stand mixer head with mixer paddle attached for proper clearance between bowl and paddle. See your mixer manual for adjustment procedure

I did exactly what the PartSelect video demonstrated after watching other DIY videos on the Internet, thus I did not remove the stand which seemed like a little too much for a simple straight forward repair. This is the second time I have replaced this gear. The first time was about 10 years ago when the bakelite gear broke on a 30 year old KitchenAid K
-45. That mixer made hundreds of loaves of bread after grinding many pounds of wheat berries. The only reason we had to replace it was that it walked off the flour dusted counter and landed on its head when my wife had her back turned. Otherwise we would still be using it. :-)
Thanks for the excellent service and instructions.

Found control backplate out of adjustment. Should be nominal 3/8".Broken speed control spring which attaches to backplate bottom.
I recommend Loctite Blue to complement locknut's when adjusting RPM of "Stir" speed

The shield works sufficiently. Note that the shield is not a continuous circle as shown in the picture. This actually can be an asset because it can be installed or disassembled without stopping the mixer of having to lift the head while running.

I took apart the mixer housing and removed all the screws. The most difficult part was the two pins that needed to be removed with a metal punch. They were in fairly tight. The mixer came apart pretty easily and it was obvious which part needed to be replaced as it was broken and missing teeth. After replacing the gear and applying new grease for smooth operation, I simply put it back together and it has worked like new ever since.

You tube has great instructions! I would suggest when you buy a part to let customer know that they need a food grade gear grease ordered to complete the reinstall of all gears and body parts!

I had a sourdough batch get into the space where dough hook attaches and it got so stuck that nothing - not hot water baths, not pliers and screwdrivers got the dough hook released. I had to open up the mixer following partselect you tube instructions and replacing the parts. What was confusing to me at first is that my 45 year old mixer had an extra screw on top of the shaft that no longer is there for newer models. It took me longer than I am willing to admit to figure that the extra screw is not the result of me skimming the instructions - the original shaft and dough hook went to a friend who broke it attempting to disengage the two parts (the dough turned out to be a very strong form of glue!). The piece is working like new. I preferred the agitator shaft with a spring to hold the end piece tighter, but the new set up without a spring works just fine.

I am not handy, but was able to follow this YouTube video and do this repair easily and successfully: https://www.youtube.com/watch?v=1QsgPIL9FpA

I did take the mixer apart first to verify that the worm gear was the issue, then ordered the part from you site. I received it quickly and was able to do the repair and get back to mixing in a few days!

watched how to repair