Models
>
5KP2670
5KP2670 KitchenAid Mixer - Overview
Models starting with 5KP2670
Click on the best match to narrow your results.
Keep searches simple, eg. "belt" or "pump".
Worm Following Gear
PartSelect #: PS12070620
Manufacturer #: W11086780
This gear is used to power your stand mixer. It is attached to the planetary shaft. The gear can become stripped over time or accumulate grease. You may need to replace other mechanical parts at the s...
$18.30
In Stock
Retaining Ring
PartSelect #: PS11746909
Manufacturer #: WP9703438
This part is a retaining ring, sometimes called a retaining clip, that holds the drum support roller onto the shaft of a dryer. It is made entirely of metal and measures less than an inch in diameter....
$7.88
In Stock
Hub Gear
PartSelect #: PS12348886
Manufacturer #: W11192795
Includes both the attachment and beveled gear. This worm follower gear is for stand mixers.
Worm follower gear meshes with the worm gear, causing the rotation of the planetary assembly where the ac...
$22.09
In Stock
Thumb Screw - Black
PartSelect #: PS11747009
Manufacturer #: WP9709194
This part is used with the stand mixers attachments, as well as to hold the end cap to the front of the mixer.
$23.40
In Stock
Stand Mixer Speed Control Board and Knob (Black)
PartSelect #: PS11746947
Manufacturer #: WP9706648
This assembly includes the black knob. Used with Stand Mixers.
$87.52
In Stock
Retaining Ring
PartSelect #: PS11746917
Manufacturer #: WP9703680
Used on Stand Mixers.
$8.99
In Stock
Retaining Pin
PartSelect #: PS11746974
Manufacturer #: WP9707223
This part works in conjunction with the worm and bevel gear.
$9.03
In Stock
Stand Mixer Gear Grease
PartSelect #: PS12583821
Manufacturer #: W11200218
This Stand Mixer Gear Grease lubricates the moving parts of the stand mixer.
$65.05
In Stock
Gearcase Housing with Gasket
PartSelect #: PS1871466
Manufacturer #: 8212396
NOTE: This part has been upgraded from plastic to metal housing. Gasket is no longer available separately.
***Used with Stand Mixers.
$60.08
In Stock
Thrust Bearing Kit
PartSelect #: PS11746911
Manufacturer #: WP9703445
This bearing comes equipped with two washers and is used on stand mixers.
$15.73
In Stock
Common Symptoms of models starting with 5KP2670
[Viewing 3 of 3]Noisy
Fixed by
these parts
these parts
Show All
Touchpad does not respond
Fixed by
these parts
these parts
Show All
Leaking
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
wouldnt turn beaters
removed metal strap around motor housing then remove the 4 screws holding top motor cover on, then removed the 4 screws that hold gear cover in place, remove long gear that is driven by the motor gear, then with ring pliers remove ring off long drive shaft and lift off worm gears. once all gears are removed --removed all the old grease (
... Read more
do this to get all the metal shavings out from the failed gear) repace the grease in the gear housing and reassemble in reverse order
Read less
Parts Used:
-
Barry from Rowland Heights, CA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
91 of 100 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Mixer Made Very Bad Grinding Noise, And Would Skip While Making Bread Dough
1, Removed trim piece (1 screw) 2, removed cover (4 screws) 3, removed speed switch assembly (2 screws) 4, removed gear cover (4 screws) 5, removed and examined 2 worm gears for wear. Gear cover was badly cracked, don"t know if it was caused by a previous repair or by heat, as old cover is plastic. Received new parts and installed them
... Read more
, 2 bearings, 2 worm gears, 1 new cover of diecast metal and a new gasket. All repairs made with a #2 phillips screw driver. My wife then made bread, and it preformed flawlessly.
Read less
Parts Used:
-
Dennis from Lake Mills, WI
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
75 of 88 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Plastic gear housing in stand mixer fractured causing gears to crash
Removed four screws to remove main cover. Removed four more screws to remove fractured plastic gear housing cover. Removed retainer ring and slid two gears and dowel off main shaft. Lifted out remaining gear train and bearings, Removed all grease and metal chips from all components. Greased new gears and reassembled. Replaced plasti
... Read more
c gear housing cover with oreviously purchased die cast replacement part. Assembled main cover.
Read less
Parts Used:
-
WES from BREVARD, NC
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
66 of 99 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!