Refigerator door was not closing all the way if not pushed shut.
Remove the top hinge cover. Removed the top hinge support. Lifted the door from the bottom support. Old door cams were worn completly flat. Replaced the lower door cam and closing cam use a little vasalene for lubricant on the cam surfaces. Placed the door back on the lower hinge support. Replaced the top hinge support. Door is closing great now. Thanks for the quick part deliver.
Simply pulled out old drawer and replaced with new one. This broken drawer really bothered my wife so this simple repair earned me alot of points at home. Lord knows i can use all the extra points i can get. Thanks for the quick shipment of the part. 2 days from time of call to part on my door step. Thanks again
six months the light turns red. time to replace filter
First I shut the water off to the refrigerator.then i pushed the big button in the middle of the grille below the refrigerator door. pulled out the old filter, took the front cap off the old filter put it on the new filter. took the two red caps off the new filter. pushed the filter in till it locked in place. all done! Turned the back on.
We waited two years to do this because we didn't want to hassle with a repair man to come out and charge us arm+leg for something so simple. Finally we searched and found the part on line. It came two days FASTER than promised. Kudos to Part Select. Snapping it on was a breeze, although you do have to apply more pressure than feels comfortable with plastic clips. We can know get ice out of the external door system again.
The Water Dispensor Tubing Had Become Brittle And Broke .
Removed the face plate. Removed a few screws and unpluged a few electrical connectors and pulled apart. Removed the holding bracket and clear tubing from door. Cut new tubing at an angle to push through conduit. Reinstalled new bracket and re-installed electrical connectors. Snapped face trim on and bleed air out of system. . Water ran great.
1. 1/4 drive socket and standard socket 2. On top of door .... remove black plastic bracket cover on top of hinge 3. Have someone hold the frige door in place 4. On top of door .... remove 3 screws that hold the hinge onto the frige..... at this time, door will be loose 5. Lift door up and off the bottom hinge. 6. sit door on the ground. Tilt door at an angle for access to the "cam" 7. On frige, at the bottom, use socket to remove one screw that holds the old "bottom" cam in place..... then replace with new one. 8. While door is tilted, use socket to remove one screw that holds the "top" cam in place. 9. You will need to gently pull this cam out.... shouldn't take too much effort though. 10. Replace with new cam. 11. put door back on hinge 12. At top of frige, reinstall 3 screws 13. Reinstall plastic cover. 14. Voila, you're done
It's simple enough in theory: read the side of the box and follow the instructions. BUT you need to really push the knob in pretty hard (I am a girl, and my hand strength isn't that good). If you don't, when you turn the knob, the filter won't come out, then it's tougher. So: make sure the knob pops before you turn!
where ic e dispencer spring is held to door broke at mold
after ordering ice dispencer repair kit, and removing the outer parts found out that the problem was the ice dispencer door shell . this part is no longer available.It seems to me that if whirlpool wants to have return customers they have to stand behind the product. Well I made a L bracket and drilled a hole to to recieve the spring keeper and glued this to the housing and used a 3 1/12"finishing nail as the pin all works fine
Patience is a virtue. The kit really works. 1st, lift the front plate of the ice dispencer by placing a flat head screw driver into the two slots at the bottom of the panel. When the panel is lifted up slightly at the bottom, push up on the panel to remove it. Careful not to break panel and the wires attached. Next, remove the wiring panel by removing the two screws on left and right sides. Then, unplug the old black ice cover from the wiring panel (this is the heating plug that you will nolonger need). Next, remove the parts and replace them with the parts in the kit, noting where each part comes from, etc. All parts in the kit are necessary and should be used. Some of the replacements need trial and error. Patience will be important. Also needed is a person that loves to solve problems, especially because the kit does not come with instructions. But the kit definitely works!
It was ridiculously easy. Push the button on the filter canister holder at the base of the refrigerator and the spring-loaded mechanism came out smoothly. I unplugged the old filter, took the cap off the new on and plugged it in. After reinserting the filter canister holder and locking it in place, I heard the whoosh of water once again moving through the filter. Very satisfying and very easy to do.
First I opened the fridge and removed the broken drawer. I then removed the new drawer from its shipping container and placed it on the tracks in the fridge. I then closed the fridge. Perfect!