59675522400 Kenmore Refrigerator - Instructions

I used a knife blade to slip under the edge of old switch to pray it out of the hole it was inserted into, switched the wires and replaced the new switch into the same hole. It took about five minutes!

removed the drawers and shelf. removed end cap with a socket replaced new part, reinstalled drawers and shelf. probably took 7 minutes start to finish.

Unlike what the online video showed, my bottom freezer French door refrigerator didn't use hooks to secure the icemaker in place. Instead, it used three tabs with screws to secure it in place. I could see two of them, but not the third one. After removing two screws and realizing that the icemaker was still pretty well secured, I felt around and found the third screw (at the top, right behind the front of the icemaker). Once I got that out, the replacement went easily, as shown on the video. That third screw was a little challenging to put back, but after a few tries I got it in. The icemaker is now making ice like a champ! Good work PartSelect! And the part came quickly, as advertised.

It was easy, since I took the old one out, I knew what to do to put the new one in. Not problem, just a couple of screws!

Easy to replace part - remove panel at the bottom rear of the appliance, unplug from the compressor and connect the new relay. Unfortunately, it was not the relay on my appliance -- looks like the compressor has gone out -- new fridge for me

First pulled the Ice tray out of the freezer, Pulled the cord for the power to the refrig. Removed 3-Srews with the nut driver and disconnected the Power Supply to the Ice maker. Removed it from the freezer and started to remove the Bail and install the bail in the new Ice maker. Remove the cover from the side of the old ice maker and install it on the new ice maker. Put it back in the Refrig and connected the power cord and installed the 3-screws and reinstalled the Ice Tray and 30 mins. later it started making ice. Thanks for the Youtube Video it helped a lot to take the pressure off of doing it your self.

The annoying cover to the deli drawer broke off again. This is my second time purchasing this part from this website (left side and now, right side). Both purchases were very easy. Replacing the left side is easier because there isn't a temperature adjuster to remove and reinstall. I found this website very easy to find my parts both times, and I installed the right side (the latest fix) in less than 15 mintues while taking care of two kids. Many women do repairs around the house and are successful! :)

The repair is staightforward. Simply remove the deli drawer (up and out), the glass lid, and the vegatable drawers above it (easier access- they just slide out). Using a 1/4 socket I removed the 3 screws holding the end cap in place. You then disconnect the 2-3 places where the end cap connects to the humidity adjustment (front and rear). When the end cap is out you have to remove the drawer slide as and humidity adjustment slide as it isn't included in the replacement part- just 3 more screws- same size). Attach the drawer slide to the new end cap and do everything in reverse to replace it. Took all of 20 minutes including cleaning/drying the drawers etc while I had them out. Easy project.

Disconnected power--removed ice holder tray--removed ice maker end cap--disconnected electrical wires--removed one screw holding ice maker to refrigerator--lifted up on ice maker to remove it from two holders--took control wire from old icemaker and installed it on new one--reinstalled new icemaker in reverse order.

Replaced the water filter with the bypass plug. The water in western NC is perfect out of the faucet.

Rmoval and replacement is not at all complicated. (1)Reach behind and to the left of the icemaker and release the power plug. There is a release snap on th side of the plug. (2)Using a 1/4" nut driver remove the screw holding the icemaker to the "L" bracket at the bottom of the icemaker. (3)Using the nut driver loosen two self taping screws holding the top of the icemaker to the side of the freezer compartment.(4)Lift up on the icemaker to remove it. (5)remove the white plastic cover from the front of the icemaker (pry out at the bottom) and snap it onto the new icemaker. (6)Remove the wire sensor arm from the old icemaker and place it on the new one. (7) Remove the cable assembly (plug) from the old icemaker and fasten it to the new one. (8)Secure the new icemaker in place using the reverse order as the removal. The icemaker will take a little longer to make its first batch of ice as it will have to attain its proper operating temp (0 degrees to 2 degrees F).

Followed your internet instructions. Saved $1200!!

we only had mm sockets so had to go to the hardware store when we found they would not fit. We needed and american socket i/2 way between #6mm and #/7mm which turned out to be a 1/4 inch socket

I ordered the grill without listening to the advise given by the operator and ended up reordering the correct part. Ya just gotta listen to the people who know or else. But The order was filled in record time with absolute perfection and the instalation went fgast and easy. Now, my wife is a very happy camper... thanks to the very kind, helpfull and professional folks at PartSelect. Lamont.

I took all the food out and the shelves above the area. The end cap was a piece of cake to remove, only two screws to take out, and installing the new ones was very easy.The reason it took so much time is because I thoroughly cleaned the fridge at the same time.