Models > 59673503201 > Instructions

59673503201 Kenmore Refrigerator - Instructions

All installation instructions for 59673503201 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 59673503201
661-675 of 864
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Ice maker was dripping and creating a giant ice block

  • Customer: Sharon from Saint Augustine FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I never would have imagined that my husband and I could replace our ice maker so easily. We simply fired up the step-by-step video on my tablet, paused it as we did each step and voila! Usually there is a lot of cussing with any repair we do and I don't think there was even one cuss word uttered. Thank you for the clear and concise instructions!

The ice maker stopped working and left "kling-ons" in the tray. At one time the trays kept trying to fill which only sent water pouring into the freezer compartment.

  • Customer: Patrick from Fairfax VA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Searching Google and Youtube produced trouble-shooting guidance to first check the water inlet valve which I did. I should have realized the valve was working since the ice-maker was trying to fill the trays. Additional advice recommended skipping all the other component troubleshooting and merely replace the old unit which I did. The big difference with the Amana appliance was the icemaker was installed laterally in the back of the freezer rather than longitudinally with the end of the control wheel positioned towards the front of the freezer. This created a tight fit in removing the old unit, especially since the wiring harness was extremely short. The latter made access to the plug release catch difficult. I used a small flat blade screwdriver and worked mainly by feel to release the plug catch. Persistent wrangling finally got the plug detached and the unit free. The water inlet hose also had a rear access orientation while the replacement unit had access was from the side. The hacksaw blade was used to cut a pre-outlined access to allow the hose to enter from the rear as with the old unit. Once the shut-off bail was transferred, wiring harness reconnected, and water inlet positioned and clipped into place, the mounting screws were secured. Within 24 hrs the first ice cubes popped and the unit has filled the ice reservoir. Keep in mind I just ordered the icemaker and did not need any other add-ons like a different wiring harness which seemed to work fine. Confirm when you order you don't need any additional parts. Good service for PartSelect. I will use them again.

Ice maker started spilling water and then stopped making ice

  • Customer: Daniel from Chicago IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
1. Watch the video. 2. Save your old ice maker's cover, metal lift bar, and power cord and clip. New one does not come with the cover, metal lift bar and power cord and power cord clip 3. My ice maker had three screw. two on top that only need to be loosened. on e on the bottom that has to be removed

follow the video that PartSelect has online

  • Customer: Rich from Wickenburg AZ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Watch the video and then do the repair.

Replace Ice Maker

  • Customer: Terri from Manhattan Beach CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
The fix was relatively easy but I could not get 2 of the screws removed. They were in very tight and I didn't have the right tools. Also, in the Amana refridgerator, they are in a "difficult to get at" location. I called my plumber friend and he helped me. Once the screws were out, the rest of the job went very smoothly as others have described. We took out the bad icemaker and reconnected the new one to the existing harness. I had ice in an about an hour. Thanks so much, PartSelect. The delivery was quick and the install was as many described on your website. You provide a wonderful service for the "do it yourselfer". Terri

Ice maker not making ice

  • Customer: JOHN from SAINT PETERS MO
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
First of all, I do not consider myself very handy. Most of my simple home repair projects include at least 2 trips to the local hardware store and take twice as long as they probably should. So if I can do this anyone can. For once, rather than just blindly throw new parts at a problem I did check the water pressure to the icemaker first and then even tested the icemaker with a multi-tester to determine what was wrong. I had $5.00 mulit-tester in my workbench but had never actually used it before, so I found step by step instructions on another website on how to test the motor and it turned out that one of the circuits in the main motor was in fact bad. Since the motor was around $80.00 dollars and the Whole unit that's inside your freezer is about $120.00 I decided it was best to just go ahead and replace the entire unit rather than just the motor. From what I saw online normally replacing an Ice maker is fairly simple. Remove 3 screws swap the prewired plug along with the metal arm then just reinstall it. Somehow whenever I try a home repair it's never that simple. First of all, our freezer is on the bottom so removing the screws holding the ice maker meant that I had to climb over, around and under the freezer shelves in order to get to the ice maker itself. Also one of the screws is not visible from the front so I had to hold a mirror in one hand while I tried loosening the screw with the other. Since the metal arm that turns off the ice maker is not included in the replacement it had to be moved over. Of course it was stuck, so it did take a little time to get it loose because I was being careful not to bend it and have to order another one. Finally installing the new icemaker meant once again that i was climbing over under and around the basket in the bottom level freezer. There is probably an easy way to remove the entire drawer but I couldn't find the release tabs so when just pulling harder on the drawer didn't work, I thought it best to just work around it. Still all in all, not a difficult job, just a little time consuming. The guy in the video did the swap in about 6 minutes, it took me about 45.

The ice maker was leaking into the holding container and had black chips of paint or plastic from the inside of the icemaker

  • Customer: Gerald from Waukesha WI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Installation was really easy since the replacement part was identical to the OEM part. Removed the three mounting screws with a nut driver. This allows one to remove the icemaker from the wall and disconnect the wire harness plug from the icemaker. I never unplugged the harness from the rear wall of the refrigerator. Put the new icemaker in place, making sure to place the water fill tube in the proper hole. Plugged the wire harness into the new icemaker and tightened the three mounting screws. The icemaker worked perfectly from then on with clean ice cubes and no leaks.

The ice tub corroded so the ice would stick.

  • Customer: Hal from Marathon FL
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Couldn't believe how complicated this part is with heaters. It is used in at least a billion refrigerators and functions well. But I had to tear it all apart to adopt it. Got it all done and stayed awake all night for waiting for Ice. Nothing! Then a Erika moment! Turn the ice arm full switch off! Then Ice poured out every hour. Expecting many years of ice. Thanks for speedy delivery especially before Christmas..

new prob. ice dispencer door seal leaks

  • Customer: vern from lake placid FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
need instr. to repair

Ice maker was dripping water in two different area's

  • Customer: Michael from Maplewood MN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
The repair was a lot easier than I thought. I first ordered the ice-maker part from PartSelect. Followed the instructions from the how-to video and I was done within 30 minutes. Unplugged the fridge, took out the two 1/4" nut screws holding up the ice-maker, disconnected the wiring harness and then re-attached the new ice-maker in reverse order. Had to use some of the parts from the old ice-maker, like the cover, ice wire (the wire that moves up and down, letting you know when the ice box was full or starts the ice-making process) The whole process along the PartSelect video made it easy.

ice maker not making ice

  • Customer: George from Sedona AZ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I watched the video which gave me confidence that I could do the repair which I did in very little time. One thing to emphasize though: When you remove the vertical wire connector from the back of the freezer compartment, remember which color wire is on the top. I needed to watch the repair video a second time to be able to make that determination. Probably the repair video should have mentioned keeping track of that connector regarding the re-connection of it because it could also connect when turned 180 degrees.

Ice Maker wouldn't make Ice

  • Customer: Michael from Ventura CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I watched a youtube video and completed the repair in less than an hour from start to finish and save myself a service charge. It was fairly easy, the only problem was that it was a bottom freezer and getting to the ice maker was harder than if it was a side by side or top freezer.

We had water going to the Refrig but no Ice

  • Customer: Joel from Walnutport PA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
First pulled the Ice tray out of the freezer, Pulled the cord for the power to the refrig. Removed 3-Srews with the nut driver and disconnected the Power Supply to the Ice maker. Removed it from the freezer and started to remove the Bail and install the bail in the new Ice maker. Remove the cover from the side of the old ice maker and install it on the new ice maker. Put it back in the Refrig and connected the power cord and installed the 3-screws and reinstalled the Ice Tray and 30 mins. later it started making ice. Thanks for the Youtube Video it helped a lot to take the pressure off of doing it your self.

Water was dripping into ice bin as long as icemaker was activated (bar lowered)

  • Customer: Derek from Murphy TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Based on comments I read at this web site, I first ordered the water valve; that did not fix the problem. Replacing the icemaker did fix the problem. It was easy to replace. Contrary to the instructional video, I couldn't simply tilt out the icemaker at the bottom after removing the lower screww; I had to loosed the two top screws as well. The leak was caused the coating on the icemaker being cracked and peeling.

Leaking icemaker

  • Customer: Annette from Peoria IL
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I used the video on your website. It made me feel very satisfied that I was able to do it myself!
All Instructions for the 59673503201
661-675 of 864