Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 59673503200 > Instructions

59673503200 Kenmore Refrigerator - Instructions

All installation instructions for 59673503200 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 59673503200
76-90 of 870
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

My icemaker started leaking water into the catch basin and turning my ice into one big ice burg.

  • Customer: gary from carleton, MI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 6 of 6 people found this instruction helpful
Well folks I put up with an ice burg all summer when I really should have took the time to fix it. You know how it goes though. You get so busy you just put it off.
Well don't put this one off because this is just how easy it went.
I came home one evening and wanted to make a drink to relax but that big glob of ice was there waiting for me. I took a crewdriver and beat it down so I could pull the catch basin out. Having looked it over for a minute I grabed a nut driver and took three of the screws out that held it in. I unpluged the wire and bingo it was out. Maybe five min. had elasped.
After taking the unit out I notice how the non stick surface was coming off of the tray and that explains the black pieces that were getting into my ice.
Getting the model number off the back of the fridge and writing it down I went to my trusty lap top and did a quick search for a ice maker for my Jenn Air refrigeraton and blamo...! Part Select came up and I put the part number in their search engine and bingo again there it was, my part.
One quick order and in three days it was right there by my door when I got home.
Now i'm so excited. I went into the house and didn't even chage out of my dress clothes. Within five minutes it was in. Now I just had to wait for the timer to do it's thing and sure enough, I awoke the next morning to a whole tray of beautiful ice cubes. Wow no more ice burgs.
The moral of my story is I spent so much time hacking out that glob of ice and for fifteen minutes of my time, I could have been siping on cold ones by the pool but now old man winter is pressing down on me and I guess a lesson learned was a lesson earned. Fix it!

No ice

  • Customer: Jon from Boise, ID
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 8 of 12 people found this instruction helpful
1 screw remove assembly. Unplug cable harness and remove old cover and wire arm. Replace cover and wire arm and attach wire harness on assembly end. Re attach using screw removed in first step. Plug in wire harness. Making ice within 30 minutes.

My old icemaker lost some of the nonstick surface and the ice didn't want to come out

  • Customer: Thomas from Ruth, MI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 6 of 7 people found this instruction helpful
I unhooked the wire harness from the ref. and took out three screws and pulled the old unit out. I than changed a few parts from the old icemaker to the new and reattached the new ice maker to the ref. and plugged the wire back in. everything is working fine. No problems. Also I was very happy with the ordering process. Thank you!!

Icemaker would not fill with water.

  • Customer: Linford from Cedarville, NJ
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 7 of 10 people found this instruction helpful
Removed screw under ice maker. Tilted ice maker up to remove unit from upper two screws. Disconnected plug at rear of freezer. Attached wiring harness, baler arm and cover from old to new ice maker. Reinstalled in reverse order. Had ice within one hour. Very easy fix.

evaporator coil in freezer section fozen solid, refer not cool

  • Customer: Michael from Tucson, AZ
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 8 of 13 people found this instruction helpful
To remove freezer door, push white tabs, inside rail toward back, remove door and rails as one unit. Unscrew plastic rail support on one side, remove ice maker, then back panel. Cut off thermostat, strip old leads, match colors, twist copper wires together, then crimp on new part using connectors provided. Reassemble, hardest part was figuring out how to remove freezer door. Check for continuity between heater lead and white terminal of icemaker plug just to make sure the heater is good while everything is apart.

Freezer too warm(everything melted), refrigerator too warm

  • Customer: John from Swarthmore, PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 6 of 7 people found this instruction helpful
Using socket wrench, took bottom right panel off on back side of refrigerator to expose compressor. It was very hot to touch, with no noise, signifying it wasn't working. It was a Tecumseh, TP142ar229b8. Evidently from internet search this is not a good brand. Turned off power at circuit box. Removed metal spring clip holding on white relay. Took off capacitor (black square piece) attached to relay. It was okay as I measured 15uF with multimeter. Disconnected electric cables to white relay by pulling off connector. Took off white relay with long cylindrical protrusion from compressor by pulling it straight off. Shook relay - pieces of ceramic fell out, indicating it was bad. Ordered and received new one (next day). Attached new relay to existing compressor by pushing it on. Replaced capacitor and electrical cables by pushing on. Replaced spring clip. Turned on power and compressor was working. Replaced bottom back panel.

The ice maker stopped making ice.

  • Customer: Thomas from Cupertino, CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 5 of 5 people found this instruction helpful
I did a few tests with the old ice maker and determined that it was the ice maker itself that was faulty. The replacement part I ordered exceeded my expectations in the time it took to get the part. I reused the arm, wire harness and clamps from the old icemaker. Then it was a simple install into the bottom freezer compartment, turning on the water supply and bingo...lots of ice cubes.

Light switch rocker broke, disabling freezer internal light, water dispenser, and ice dispenser

  • Customer: Kenneth from Newton Grove, NC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 6 of 8 people found this instruction helpful
Very simple. Matched female plugs with respective male color coded prong; pushed together then inserted unit in slot of freezer sidewall and rotated into position...job done.

The orignal proberm was broken hinge on End Cap

  • Customer: David L. from Red Rock, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 5 of 5 people found this instruction helpful
There was little or almost nothing to change out the End Cap, two screws on the End Cap and two screws on slide. It took longer to removed and replace the two drawers and shelve than it did to replace the End Cap. The part I ordered was exactly what I needed.

Broken tab that holds the pantry door on

  • Customer: Craig from Pueblo, CO
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 6 of 8 people found this instruction helpful
I broke the left side end cap the holds the pantry door on.
I search the internet for the part and happened to run across part select. I order the part and received the part with in 3 business days. It took less than 30 minutes to replace the end cap.

The great reviews help me with my choice to order the part from part select. I will order parts from them again.

Thanks for helping me fix my fridge.

no water pressure, and very little volume of water

  • Customer: Robert C. from Milford, PA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Wrench (Adjustable)
  • 9 of 17 people found this instruction helpful
First I removed the existing copper ice maker line and then installed a plastic line. I then tried the appliance, with no change. I then removed and replace the primary water valve and then tested that as well. There was no change in the outcome. So I removed and replaced the secondary water valve and tested that as well and I noticed a significant change in water pressure, and in volume.

a piece broke off that caused a shelf lid to not open and close correctly.

  • Customer: Denise from Sammamish, WA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set, Wrench (Adjustable), Wrench set
  • 6 of 8 people found this instruction helpful
It was a very simple operation and was done in no time.

Doing it myself saved me at least $100.00 or more.

I was very happy and satisfied with the part and how doing it myself saved me a lot of time and money.

Freezer cold, Refrigerator warm

  • Customer: Randall from Nashville, TN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 7 of 12 people found this instruction helpful
I did some research online, and was sure that it was the evaporator fan motor that was not working. So I paid more for overnight shipping than I did for the fan motor to have it over-nighted. I removed the botttom freezer door by simply pulling out and lifting it up. I then removed the wire shelf by pulling it straight out. Removed the ice maker by removing the three screws that held it in place . Disconnected the the wire harness, and pulled it out. Then I popped off the plastic vent at the top of the freezer's interior rear cover. Removed the rear cover by removing the four or so screws holding it on to expose the evap fan motor and the freezer coil. Careful, the fins are fragile and sharp. I inspected the fan motor and it seemed to be working fine. I unplugged the fridge and plugged it back in. It went through a defrost cycle and I put it all back together again. Cranked the frige unit up to 7, and was able to lower the freezer to 4. It's been working ever since. Eventually I was able to lower the fridge back down to 6. Long of the short is I paid $60 for nothing.

Broken Piece

  • Customer: anthony from georgetown, IL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 5 of 6 people found this instruction helpful
Had to disassemble ice maker to install part. . .

Tab for deli cover broke off...after 1 year ordred part,

  • Customer: Cranson from San Francisco, CA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 5 of 6 people found this instruction helpful
Took off old cover 3 screws...removed metal track and 2 other plastic sliding bars for air flow..put on new cover and carefully put back deli cover on plastic pins..easy fix...lousy design by maytag again! Thanks to PartSelect easy and prompt service and delivery!
All Instructions for the 59673503200
76-90 of 870