Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 57731H8WW > Instructions

57731H8WW General Electric Washer - Instructions

All installation instructions for 57731H8WW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 57731H8WW
76-90 of 397
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Water leaking from filler hose outside of tub

  • Customer: Paul from Talihina, OK
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 7 of 11 people found this instruction helpful
removed washer front panel, top panel to access the water fill spout and hose. Disconnected and replaced.
personnel at part select were very knowledgable about detailed part and the overnight service was right on time.
I would recommend part select for your next appliance parts needs.

Broken knob on my Mom's washing machine

  • Customer: Edward from New York, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 5 of 5 people found this instruction helpful
Folks,

Thanks to your great web site and help video I got this fixed in less than a minute. Literally less time than it took me to watch your helpful video. Don't know how to thank you - keep up the good work!

Dial Spins Too Freely

  • Customer: STEPHANIE from Bluefield, VA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 6 of 8 people found this instruction helpful
The grooves on the bottom of the control knob were worn away. I just pushed the timer knob clip off of the underside of the knob, removed it from the washer and put the new knob on and put the clip back on. It was a piece of cake!

Huge Banging, Uneven Spin, Metal Fragments in Tub

  • Customer: Daren from Bloomington, IN
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 6 of 9 people found this instruction helpful
After reading all the repair info and reviewing the diagram for my wash machine on this website I was ready to tear into my washer. I removed the front panel and lid to access the tub, pulled out the plastic agitator and revealed the broken inner base hub. The base hub was cracked half way around causing the inner tub to drop down and drag on the outer tub, making the washer sound like it was coming through the wall on a spin cycle. I then unbolted the plastic cap and removed it revealing the hub nut. The most valuable piece of advice in the repair info was abouthe hub nut being a laft hand thread (clockwise to loosen)and that it was on really tight and hard to remove. I put a short 8" pipe wrench on it, because of the lack of clearance in the tub, and hit it with the handle of a all steel hammer to break it loose. Unbolted the balancing straps (4) on the plastic top rim cap that holds the tub in place, unsnapped and removed it, then carefully pulled out the tub. I also had to unscrew the the control panel to reveal and remove the 4 screws holding the fill tube brace so I could push it back to remove the tub. I then took the inner tub outside and took it apart, 3 parts. The top plastic rim, the tub, and the broken base hub that are held together with torx screws. Then it was cleanup time, very dirty on the inside, used a garden hose, scrub brush, sponge, and soap. Cleaned up the hub nut threads with a wire brush and then the outer tub withe a sponge and shop vac. When the base hub broke it caused the inner tub and outer tub to rub together making a groove and plastic shards on the bottom of the outer tub that I had to scrape and sand smooth. A shop vac an absolute necessity in getting all the grime and plastic crumbs out of the outer tub so they don't get in and clog the pump. I received the replacement parts in 2 days! Reassembled in reverse order and everything worked great! Not a bad project at all when you know what to expect, thanks to Part Select.com.

Dampening straps were broken

  • Customer: Marc from Cambridge, MA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 5 of 6 people found this instruction helpful
Originally my water level sensor was broken. When I was repairing that, I noticed that the dampening straps were broken. Replacing them was easy. The hardest part was remembering how to open the top. I just searched the internet until I found the answer. I can't remember it all right now, but the key was to slide a putty knife in between the top and the front to pop open the body.

Tub straps broken caused excessive wabbling

  • Customer: Drew from Apopka, FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 5 of 6 people found this instruction helpful
Popped off the front panel and removed two screws that help top down. Then pulled the top of the washer up and leaned back out of way.Then each strap had a screw on each end and a clip that holds straps just remove the old and replace with new and put back together.

Broken tub strap, hub, an cracked outter tub

  • Customer: Drew from Queen Creek, AZ
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
  • 5 of 6 people found this instruction helpful
Repair went good, only wish i had bought a new tub seal, washer, an split ring....but i managed to save the original ones an it seems to be working like new again! thanks Partselect!!!!

Hub broke around center

  • Customer: Thomasq from Rixford, PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
  • 5 of 7 people found this instruction helpful
Removed the front panel and lid.
Removed the ring on top of tub and holder.
Had to use a rope and pry board to get the agitator off the shaft. Removed the 7/16 cap screw and removed the plastic agitator block.
Couldn't get the hub nut off and had to use a chisel to break it off (corroded and a left hand thread).
Had to use chisel to free the hub from the center pieces so I could lift out the tub. Then I had to hammer and twist the center piece of the hub to get it off form the transmission shaft.
replace in reverse order without any problem once I realize I had a left hand hub nut.

washer barral spins with loud noise, turned out to be the worn Wahser Hub

  • Customer: shaobo from fremont, CA
  • Difficulty: Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
  • 6 of 10 people found this instruction helpful
1. take the machine apart, since the noise comes when the barrel is spining, I just watch for anything that contact to the axel.
2. without special tools, it was difficult to take off agigator, and a nut (that tighthened lefthanded).
3. Once defect part found, seach online for the part supply to replace.

Water wouldn's stop running

  • Customer: Amy from Newport, NC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 5 of 7 people found this instruction helpful
First removed the screws on the contraol panel. Then I pulled the tubing from the part. Snapped teh switch preesure out. Put the new one in. Attached the tubing. Put control panel back together.

Drain hose had a hole in it

  • Customer: kartik from radnor, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 4 of 4 people found this instruction helpful
used a socket to unscrew the clip. pulled out the old hose, slid the new hose into the clip and screwed the clip back on. all fixes should be this easy.

Spinning Control Knob

  • Customer: Susan from Keyport, NJ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 5 of 7 people found this instruction helpful
I watched the video, used a needle nosed pliers to pull the clip off the knob and just pushed the new knob and clip on.

some leak

  • Customer: Roberto from Nokesville, VA
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench set
  • 4 of 4 people found this instruction helpful
First, remove the old water pump by disconnecting the respective hose, then wipe the area where the pump was, and proceeded to connect the new water pump, of course I did all this with the machine disconnected from the power electric, then proceeded to connect the inlet hoses of hot water and cold water, electricity connected to the machine and did a test with clothes in the washing machine. and now everything is going well, thanks for your valuable help.
sincerely, a satisfied customer

Washer did not drain completely with water on floor, drain pump frozen.

  • Customer: Ray from Ventura, CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Socket set
  • 4 of 4 people found this instruction helpful
After unplugging the washer, I drained remaining water from washer tub using my Wet/Dry vac. Ordered new pump Sunday night from PartSelect, 'Standard delivery', part arrived Tuesday morning. Removal & installation took less than 20 minutes.

Very noisy in spin mode

  • Customer: James from Colora, MD
  • Difficulty: Really Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers, Socket set, Wrench set
  • 5 of 8 people found this instruction helpful
a) remove front panel by depressing the 2 clips at the top in line with the lid b) remove the lid switch and 2 screws holding top on and remove top by tilting up SLIGHTLY and sliding to left. c) Remove agitator and by pulling straight up on it and remove adapter underneath d)remove 4 bolts holding 4 rubber straps to top of tub assembly, readily visible when top is removed. e) unplug motor wiring and disconnect pump and bleach hoses from tub f)while lifting up on tub, push down on each of the 4 suspension rods and disconnect them at bottom of tub ( this is the most difficult part, and to make it easier disconnect the rear rods first) g) tilt tub forward and remove tub assembly h) NOW, for the big nut that holds the spin basket in-- #1, it is LEFT HAND THREAD, so you will turn it to the right to remove it. #2, it is VERY TIGHT and requires a 1&11/16" spanner wrench (which I did not have) for removal. Instead, I used a 1&11/16 socket, an extension and an air impact wrench to remove and replace the nut. Assembly is reverse of removal and remember, that nut is ALUMINUM so be careful with that impact wrench when tightening it back up!I replaced the nut and split ring and cleaned the whole area thoroughly, and it greatly reduced the noise in spin mode. I did not replace the metal housing on the bottom of the spin basket, because it was $50 bucks. this probably would have eliminated all the noise, but my repair only cost $19 in parts, including shipping ,and the parts arrived in 1 day.
All Instructions for the 57731H8WW
76-90 of 397