Models > 570WJ Maytag > Instructions

570WJ Admiral Range - Instructions

All installation instructions for 570WJ parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 570WJ
1-15 of 165
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Oven would not work but the Broiler did

  • Customer: James from Ferndale MI
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 147 of 157 people found this instruction helpful
The oven had been working intermittently for a while and after repeated threats of starvation from my spouse I finally took a look even though it was summer and the grill was working fine. The Igniter would glow red when the oven was turned on but the gas would not flow to it no matter what the temperature setting. I searched online and found this site that explained it was possible for the igniter to glow but if it was not drawing the correct amperage (because its resistance was too high) then the main brain would not allow the gas valve to open. So I took a look at the broiler and it had the same igniter. I measure the resistance of both of them and the oven igniters resistance was higher (don't rememeber the reading) then I moved the Igniter from the broiler to the oven and the oven worked from there it was just a matter of ordering the part. End of story except for I am still doing all the cooking on the barbecue outside.

Oven would'nt light

  • Customer: Charles from Charlestown RI
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 69 of 77 people found this instruction helpful
In most cases if your oven won't light or takes a long time to light you may have a bad igniter even if it glows. To check the igniter use a voltmeter to check for 120 A/C volts going to the igniter and3.5 A/C volts going between the ingniter and the gas valve. My bad ingniter glowed but had only only 3.0 A/C volts going to the gas valve for the oven. The new igniter took only 45 minutes to install and supply's 3.6 A/C volts to the gas valve and the oven works fine.

oven failed to light

  • Customer: Beryl from Dawsonville GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 35 of 38 people found this instruction helpful
My son replaced the broiler igniter this spring, so I had a clue as to what was required. This was even easier and since I had back surgery recently & my husband was out of town that was a giant plus!

I unplugged the oven, removed the oven door, found the release latch and removed the oven floor. I then removed the 2 screws that held the igniter in place (I received this stove used and the igniter had evidently been replaced before as it was the same shorter version included in the kit). I pulled the igniter out then removed some insulation and tugged the connector out of the oven floor. I disconnected the igniter and plugged the new one in. I then replaced the connector in the floor, attached the igniter with the screws, replaced the insulation and did a test run (plugged in the oven & turned it on). That was successful so I put the floor back in and put the door back on.
Ta-Dah!

Oven would not ignite

  • Customer: Jerry from Paris TN
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 26 of 28 people found this instruction helpful
This repair project was too easy!...and cheap. Sears quoted the price of the igniter at $280 plus the service call and the item cost $41 on PartSelect. The part was received the next day after the order was placed...WOW! So easy, turn off the power to the oven, open the oven door, remove the oven racks and lift the bottom pan of the oven up from the back and set it aside. There you see the flat type igniter in plain view at the back of the oven. Remove two screws with nuts using a nut driver (I had trouble because the screws were corroded and I had to use some, um, force to get them out and swore a little too). Once the screws were out, pull the igniter elecrtic wires and connector from the entrance hole in the back after moving a little insulation out of the way. Release the connector plug and unplug the old igniter and simply plug in the new one. Find new screws and reinstall in reverse order. Be sure to push the connector and wiring back into the hole and cover with the insulation. Very easy job that anyone could do.

glow bar would light but oven would not light

  • Customer: David from Van Nuys CA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 20 of 22 people found this instruction helpful
I removed the rear access panel on the oven in order to get to the igniter wires. While testing the output voltage of the old igniter when on, I found that it was producing less than 3 volts ac. This was my clue that although the igniter glowed, it was going bad and needed to be replaced. I unpluged the oven, shut off the gas feed to the oven then removed the oven bottom pan (pull two push pins back, lift up and out) and removed the burner baffle wing nut with baffle. This gave easy access to the igniter and it's two mounting screws which i removed using a phillips screw driver. I unpluged the old igniter from the connector, pluged in the new one after routing it through the access hole from inside the oven to the back of the oven where the connector is located.
Mounted the new igniter, replaced the burner baffle, baffle nut, oven bottom, rear access panel cover, checked and turned on the gas, plugged the oven back in and sure enough it fired up right away. if you check the system of how your oven works and find the problem, it's easy to fix it yourself and save serious money...and look like a hero to the rest of the family.

Oven wouldn't lite

  • Customer: E Blake from Dauphin Island AL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 14 of 16 people found this instruction helpful
Pulled off the oven door, just lift straight up. Pulled out the floor of the oven, very easy just lift from the back. The only problem I had was the screws holding the old igniter wouldn't come out, they just spun. I snipped them off and picked up two new ones at the hardware store. Pull the wiring harness in through the hole in the back of the oven. Unsnap old wiring harness, snap in new one. Reattach the new igniter, replace floor, replace door. Turn on oven and cook food... fairly easy repair.

oven takes a long time to reach temp set point

  • Customer: Scott from Brooklyn Park MN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 12 of 12 people found this instruction helpful
i need to replace the lower oven igniter about 2-3 years
unplug the oven
open the oven door half way then slide the door up
take out both racks
push the bottom pan away from you and lift up
one screw holds the igniter on
pull the wire out until you get to the electrical plug
disconnect

Oven would not light

  • Customer: Richard from Austin TX
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 11 of 11 people found this instruction helpful
This oven was located in a rental house I own.

I first removed the metal plate that covers the burners at the bottom of the oven. No tools required for this step.

Next I turned the oven to 300 degrees, waited 30 seconds and noticed that the igniter was glowing brightly, but the burners did not light.

I next turned the oven controls off, pulled the plug, and set to work removing the 2 screws holding a plate to the back oven wall and the 2 screws holding the igniter to the burner. These last 2 screws had corrosion on them and I needed to use vise-grips to get a firm hold on them. During reassembly these screws no longer held firmly because the hole they threaded into was enlarged during disassembly.

With the screws loose I pulled the igniter and fished the wires connected to it through the opening until I saw the connector. I then pulled the stove out of its opening and saw that there was a easily removable metal cover over the wires, and I took it off.

The new igniter came with an incompatible plug, so I cut off the connector on the stove wiring and on the new igniter and used wire nuts to make the new connections. I kept the orientation of the old and new plugs the same way in case the wiring mattered, but that was just being safe. I don't know if the igniter cares which of its wires go to which wire on the stove.

I reinstalled the screws holding the igniter, and shoved short sections of the supplied wiring into the screw holes so that the screws would hold more tightly. I shoved the supplied insulation into the opening that the wires passed through, and reattached the cover at the back of the stove.

I shoved the stove back into its opening, turned the oven on and it lit within 15 seconds.

I was very happy with the result, and the product I ordered arrived on time, well packaged and I'm a very happy customer.

oven comes on to temp but will not reheat to a new temp third time trouble with same range

  • Customer: william from newport VT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 9 of 10 people found this instruction helpful
first of all i have one advantage even though i am 70 yrs old i had a appliance shop for sears in the 60s and 70s and have not forgotten to much of the basics i am still in the security business and up on electronics. last time i had the company repair the oven , 70 dollars for the part 75 dollars for the svs call. (first igniter was on full warranty) well this time i decided to look for trhe part myself, i just went on line typed in oven repair parts and eventually all these sites came up. yours was the most professional looking and i took a chance. guess what everything you promised you delivered. price quality USA made parts and delivered in three days . opened package went to work less than fifteen minutes back in business.
will sure use you again if the need arises thank you

pilot lit but oven would light

  • Customer: Paul from Arlington MA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Wrench set
  • 10 of 13 people found this instruction helpful
replaced the oven safety valve. This device uses heat from the pilot to hold open a valve that allows gas from the thermostat control to feed the main burner. It works by boiling the liquid mercury in the sensor bulb, producing the pressure to hold open the valve. My sensor had failed from old age, leaking the mercury.

Spilled mercury needed to be collected and properly disposed, and the valve was a tough fit among the sheet metal parts that form the path for the gas to the burner slots. The valve is secured by flat head sheet metal screws and the gas plumbing is a tapered pipe fitting. The sensor bulb has a small steel spring to hold it in the proper spot to sense the pilot light.

I used gas-rated pipe dope on the gas fitting, probably unnecessarily. Valve faces only 1/2 psi pressure...

oven burner would not come on.

  • Customer: Theodore C. from Winsted CT
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 8 of 8 people found this instruction helpful
I am a retired lp Gas service person so this was quite
simple for me. Replaced the oven Igniter. What amazed me I placed my order and had the Igniter less than 24 hours. thank you so much for the quick service.

Oven stopped while the wife was cooking.

  • Customer: Marsha from Concord MA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 9 of 11 people found this instruction helpful
Range is 20+ year old 'condo issue' and difficult to pull from wall since previous owner had tiled it in. Going in from the back was going to be a pain.
Removed the oven door by opening slightly and pulling up. Removed grilles. Removed bottom of oven by sliding 2 latches in the back forward and pulling it up. Removed 2 screws holding igniter (long-style) to the rear of the burner. Cut power to the range and snipped the 2 igniter wires as close to the igniter as possible, leaving me only about 1 inch of wire to work with. Removed 2 screws holding old plate to rear of the back of the interior of the oven. Snipped off the connector on the new igniter. Carefully stripped about 3/8" of insulation off of all wires and used hemostat to hold wires together while applying the wire nuts. Used hemostat to work the wire nuts and excess wire back into the hole. Stuffed the hole with supplied insulation. Attached new back plate with original screws and attached igniter to burner with original screws. Reapplied power to range and did a test light. It worked, so I reassembled the rest. For me, the worst part was holding the wires together so the wire nuts would 'take', while working inside of the oven. But, an easy and successful job!

oven won't stay light

  • Customer: Shannon from Lake Park IA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 7 of 7 people found this instruction helpful
removed racks, bottom plate. removed screws with a little bit of help from cooking spray. Unclipped old ignitor clipped in new ignitor, used old screws, and inserted insulation replaced racks, bottom shelf. Turn on oven and worked, been using it for about a week now. PS. ordered on monday morning arrived wednesday afternoon.

Gas oven took longer and longer to light off even though glow igniter was glowing. When the time grew to 10 minutes and more I knew a repair was needed.

  • Customer: Joseph from West Hartford CT
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 7 of 8 people found this instruction helpful
I first removed the bottom of the oven and the flame guide to uncover the igniter assembly. Then I applied WD40 to the two Philip head screws and unscrewed them to release the old igniter. The two wire leads from the igniter went into the back of the oven and I could not reach the connection block. So I pulled the oven out far enough to get behind it and took off the panel covering the electrical wires in back. I had previously disconnected the electrical cord from the wall outlet. After I determined that I could not remove the connection block I returned to the igniter and cut the two existing wires close to the ceramic igniter assembly. I marked the top wire with a Sharpie pen so that I would not mix up the new leads when I install the new igniter. Although it was awkward to work inside the small oven space I was able to strip the insulation back about 1/2 inch and then connect the new igniter wires using the twist caps supplied with the kit. I pushed the wires back into the space and added the insulating material supplied. The igniter assembly was then installed with the original two screws and the other oven covers and flame guide reinstalled easily. After reconnecting the power outlet the oven was back in operation with ignition of gas flame within a minute or so. It was a good feeling and now we do not need to consider replacing the gas range.

Oven wouldn't ignite

  • Customer: Treasure from High Point NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 6 of 6 people found this instruction helpful
First I unpuged the Range. Then I removed all racks and bottom tray of oven.
The Ignitor is located at back of oven, paralelle to the gas bar. I removed the 2 screws holding the ignitor and unpluged the wires. Then I put on the new ignitor, perfect fit, replaced the 2 screws and pluged in the wires , then pluged in the range. I turned the oven on and it lit in about 10 seconds.
Thank you PartSelect for having such a wide range of range & oven parts . no one should have to pay a service tech. to fix most problems, as long as we have a GREAT SITE LIKE THIS ONE.
p.s. You guy also had one of the lowest prices , my part arrived ahead of schedule .
THANKS A LOT !
All Instructions for the 570WJ
1-15 of 165