Models > 57-2729-00-01 > Instructions

57-2729-00-01 Tappan Oven - Instructions

All installation instructions for 57-2729-00-01 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the oven repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 57-2729-00-01
1-15 of 18
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Cord was not tightened enough by delivery crew.

  • Customer: Timothy from Spring Valley AL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 31 of 53 people found this instruction helpful
PF alarm appeared on display. Noticed clicking when cord was moved. Had arced for some time and melted original block. New part slightly different. Only has 3 lugs, old one had six. Stack using washers provided. Take note of colors before disassembly. Use caution while working through access opening. The edges are sharp. Only tools needed are phillips screwdriver, deep socket for lug nuts. Nut driver optional. Hope this is helpful.

Oven light receptacle broken - bulb base broke off

  • Customer: Paul from Spokane Valley WA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 20 of 25 people found this instruction helpful
Turned power off at electrical panel. Pulled oven away from wall. Removed back cover (6 screws), then unplugged wires from old receptacle. I had to pull the squeeze clips backwards & break them to remove the old receptacle - couldn't squeeze them enough to remove them otherwise. The old receptacle came out through the inside of the oven, and the new one snapped in easily from inside the oven as well. Replaced wiring, installed new bulb, restored power & tested. Replaced back cover. Good time to vacuum under/behind where the oven usually lives before sliding it back to the wall.

Element showed a hot spot prior to failing open.

  • Customer: James from Delaware OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 18 of 20 people found this instruction helpful
Replaced element. Removed shelves, removed two screws and lifted/wiggles old element out to pull wires off at connectors. Reversed process installing new element and truned on to test/burn off "newness" Done!

broken carousel drive bushing

  • Customer: Galen from lowanger LA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 6 of 9 people found this instruction helpful
popped new peice on and that was it

Bad lower oven coil

  • Customer: jack from atlanta GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 5 people found this instruction helpful
turned off power, removed 2 screws replaced heater coil tightened screws.

minimal/no heat

  • Customer: Jennifer from Stockton CA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 4 people found this instruction helpful
turned off main power; took a flash light, unscrewed existing element and disconnected it from the wiring; compared existing with new elements as the shipping label said "ABSOLUTELY NOTHING MAY BE RETURNED IF IT APPEARS THAT IT HAS BEEN INSTALLED"; it appeared to be close enough but not exact. Connected wiring to new element, shoved it back into the insultation, screwed in the element with the same screws. Viola' all worked as it should. I even set my oven on the "self clean" cycle which is 3 hours on high. Overall it was very easy.

plastic bushing broke --- turntable was just a non-turning table

  • Customer: Carolyn from Globe AZ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 2 people found this instruction helpful
It took me a burnt bag of Orville's popcorn to notice that the turntable wasn't turning. After a tantrum and a bit of foul language, I Googled the brand & model. Up popped Parts Select of whom I'd never heard. THE PARTS LOCATOR IS FANTASTIC! I found exactly what I needed---checked a few other sources, but found nothing. I was a bit hesitant at ordering, but decided any site as well designed and intricate as this couldn't be a fake. Next pleasant surprise was that after ordering late Dec 26, the part was on my doorstep Dec 28! I ripped open that envelope, trotted into the kitchen, and stuck that bushing right onto the thing-a-ma-gig. That baby spun like a merry-go-round! Parts Select gets 6 out of a possible 5 stars in my book!

bake element cracked in two pieces

  • Customer: Marie from Fairview Park OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 5 people found this instruction helpful
First removed the two screws that hold the element in place.I then pulled the element out about three inches and disconnected the two wires. The new element was put in place and reconnected to the two wires.The two screws to hold the element in place wre put back in.Very easy.

replaced the burned out bake element in my wall oven

  • Customer: Donna from Guide Rock NE
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 2 of 4 people found this instruction helpful
first, I watched the video that partselect provides, then followed the instuctions that I learned from the video, I turned off the power to the appliance, removed the oven racks, removed the screws from the plate that held the oven rack in place and gently pulled it out far enough to remove the ends of the element from the electrical current wires, finished removing the burnt out element and replaced it with the new one from Partselect by repacing the new element ends on the electrical current wires and screwed it into place and replaced the racks, turned on the power and baked my pie. I am a 71 year old widow who was able to accomplish this with the good instructions provided by Partselect, this was the first time I have ever tried to do anything like this on my own.

Turntable motor was worn out - gears were slipping

  • Customer: Chad from Roanoke VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
The job was very simple, remove the bottom plate of the microwave which is four screws and it exposes the motor. There are two screws which hold the motor in place that you access from inside the unit. Remove the two screws being carefull not to lose the gasket that is in between the motor and the bottom of the unit. Set the new motor in place being sure to add the gasket to the new part and run the two screws to the new motor and tighten! It don't get any easier than that! Also do not forget to plug the motor back into the female socket before attaching the bottom plate!

Carousel Tray Drive Bushing Broke.

  • Customer: Beverly from Northwood NH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 2 people found this instruction helpful
Just had to remove the carousel tray and replace the drive bushing. And we were back in business.

carousel bushing broke,no more spin,burnt food.

  • Customer: tony from san antonio TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 2 people found this instruction helpful
Finally figured out after many months that all I needed to do was to get online and order the part. Part quickly arrived and within seconds I was back in business.

broken lens over oven light

  • Customer: Leslie from Warsaw VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 10 people found this instruction helpful
Your service was OUTSTANDING...Ordered one afternoon, and before lunch time the next day, the delivery man rang my door bell...Thanks a bunch for you excellent service.....

Control will not work - only clock blinks

  • Customer: Sue from Lampasas TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Took 3 panels off to get to the electric block. Replaced electrical block and put it back together. Still no change.

One wheel on the roller tray had a blow-out

  • Customer: Gene from Gosport IN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Trashed the old roller tray and put the new one in. Fast shipping, and dependable company to do business with. Thanks
All Instructions for the 57-2729-00-01
1-15 of 18