Models > 57-2709-10-04 > Instructions

57-2709-10-04 Tappan Oven - Instructions

All installation instructions for 57-2709-10-04 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the oven repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 57-2709-10-04
1-15 of 29
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Above 400 beeper went off & code numbers came up on read out

  • Customer: Russell from Lake Havasu AZ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 24 of 28 people found this instruction helpful
Cut off power at fuse panel. pulled stove out from wall went behind stove removed back panels in area of sensor that I could see from the front side, inside oven. Located sensor from rear & unpluged senser from wiring bundle reached inside oven & removed screws from sensor. Pulled sensor out & threaded wire through hole. Took old & new sensors to bench in shop. Plug on new not the same as old. Had to change plug Cut and stripped wires. Wire is very small, need to use a good stripper. Twisted wire together & soldered connection, used shrink wrap to insulate wire. Took part inside and reinstalled in reverse order. Used 1/4 inch nutdriver on total job start to finish.

Cord was not tightened enough by delivery crew.

  • Customer: Timothy from Spring Valley AL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 33 of 55 people found this instruction helpful
PF alarm appeared on display. Noticed clicking when cord was moved. Had arced for some time and melted original block. New part slightly different. Only has 3 lugs, old one had six. Stack using washers provided. Take note of colors before disassembly. Use caution while working through access opening. The edges are sharp. Only tools needed are phillips screwdriver, deep socket for lug nuts. Nut driver optional. Hope this is helpful.

Oven light receptacle broken - bulb base broke off

  • Customer: Paul from Spokane Valley WA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 20 of 25 people found this instruction helpful
Turned power off at electrical panel. Pulled oven away from wall. Removed back cover (6 screws), then unplugged wires from old receptacle. I had to pull the squeeze clips backwards & break them to remove the old receptacle - couldn't squeeze them enough to remove them otherwise. The old receptacle came out through the inside of the oven, and the new one snapped in easily from inside the oven as well. Replaced wiring, installed new bulb, restored power & tested. Replaced back cover. Good time to vacuum under/behind where the oven usually lives before sliding it back to the wall.

Element showed a hot spot prior to failing open.

  • Customer: James from Delaware OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 18 of 20 people found this instruction helpful
Replaced element. Removed shelves, removed two screws and lifted/wiggles old element out to pull wires off at connectors. Reversed process installing new element and truned on to test/burn off "newness" Done!

No heat when turning oven on.

  • Customer: Joseph from Edgewater FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 7 of 9 people found this instruction helpful
Started by replacing element which was clearly broken. Still no heat. So then I changed the oven sensor. Was disappointed that when I received the sensor I had to cut and splice the connector that was on it with the old one that came off the old sensor. Did that and still no heat so I had to buy a new clock/timer. Went to another store for that because of the connector not being the right type and there was no picture of the clock/timer like the other website. Overall ok, normall troubleshooting steps, just wish I didn't have to cut and splice the connector on the new sensor I purchased from here.

broken carousel drive bushing

  • Customer: Galen from lowanger LA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 6 of 9 people found this instruction helpful
popped new peice on and that was it

Oven would kick off after preheating to temp.

  • Customer: Mary from Castle Rock CO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 5 of 7 people found this instruction helpful
Sensor very accessible. Pull off the back panel, disconect the sensor and slide out from back of oven. The original plug was cut off the sensor, as well as the new one to get the proper connector type on the new sensor. Soldered and heat shrink, and presto we had our new sensor ready for install. Install was about 5 minutes which included putting the back panel on the range. Pretty easy and works like new. Total time for project was about 20 minutes.

Bad lower oven coil

  • Customer: jack from atlanta GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 5 people found this instruction helpful
turned off power, removed 2 screws replaced heater coil tightened screws.

minimal/no heat

  • Customer: Jennifer from Stockton CA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 4 people found this instruction helpful
turned off main power; took a flash light, unscrewed existing element and disconnected it from the wiring; compared existing with new elements as the shipping label said "ABSOLUTELY NOTHING MAY BE RETURNED IF IT APPEARS THAT IT HAS BEEN INSTALLED"; it appeared to be close enough but not exact. Connected wiring to new element, shoved it back into the insultation, screwed in the element with the same screws. Viola' all worked as it should. I even set my oven on the "self clean" cycle which is 3 hours on high. Overall it was very easy.

oven temp was not right

  • Customer: Kathy from Greentown PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 6 of 14 people found this instruction helpful
We removed the old part and replaced it then when warming the oven all of a sudden there was a loud noise and something went and so we called a repair man which I guess we should of done in the first place. Now he has ordered a part that cost 170 soo that is my story don't try to repair if you don't have experience.

plastic bushing broke --- turntable was just a non-turning table

  • Customer: Carolyn from Globe AZ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 2 people found this instruction helpful
It took me a burnt bag of Orville's popcorn to notice that the turntable wasn't turning. After a tantrum and a bit of foul language, I Googled the brand & model. Up popped Parts Select of whom I'd never heard. THE PARTS LOCATOR IS FANTASTIC! I found exactly what I needed---checked a few other sources, but found nothing. I was a bit hesitant at ordering, but decided any site as well designed and intricate as this couldn't be a fake. Next pleasant surprise was that after ordering late Dec 26, the part was on my doorstep Dec 28! I ripped open that envelope, trotted into the kitchen, and stuck that bushing right onto the thing-a-ma-gig. That baby spun like a merry-go-round! Parts Select gets 6 out of a possible 5 stars in my book!

bake element cracked in two pieces

  • Customer: Marie from Fairview Park OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 5 people found this instruction helpful
First removed the two screws that hold the element in place.I then pulled the element out about three inches and disconnected the two wires. The new element was put in place and reconnected to the two wires.The two screws to hold the element in place wre put back in.Very easy.

Not heating up properly.

  • Customer: Jim from Kennett square PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 3 of 6 people found this instruction helpful
What a job. Definitely should have two people do this. First, the part provided was not an exact match. I thought I was buying the same part as original. When I found it was different, there was a note that said the part may not be exact. This being said, I had to remove the wall ovens from the wall- very heavy , then had to take the back plate off, splice the wires to make the part work and then lift it up and put it back in. Next problem, its all hooked up, but still doesn't heat up correctly. Leave this to the pros.

replaced the burned out bake element in my wall oven

  • Customer: Donna from Guide Rock NE
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 2 of 4 people found this instruction helpful
first, I watched the video that partselect provides, then followed the instuctions that I learned from the video, I turned off the power to the appliance, removed the oven racks, removed the screws from the plate that held the oven rack in place and gently pulled it out far enough to remove the ends of the element from the electrical current wires, finished removing the burnt out element and replaced it with the new one from Partselect by repacing the new element ends on the electrical current wires and screwed it into place and replaced the racks, turned on the power and baked my pie. I am a 71 year old widow who was able to accomplish this with the good instructions provided by Partselect, this was the first time I have ever tried to do anything like this on my own.

Turntable motor was worn out - gears were slipping

  • Customer: Chad from Roanoke VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
The job was very simple, remove the bottom plate of the microwave which is four screws and it exposes the motor. There are two screws which hold the motor in place that you access from inside the unit. Remove the two screws being carefull not to lose the gasket that is in between the motor and the bottom of the unit. Set the new motor in place being sure to add the gasket to the new part and run the two screws to the new motor and tighten! It don't get any easier than that! Also do not forget to plug the motor back into the female socket before attaching the bottom plate!
All Instructions for the 57-2709-10-04
1-15 of 29