Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 57-2709-00-07

57-2709-00-07 Tappan Microwave Oven Combo - Overview

Get Parts and Repair Help for 57-2709-00-07

If you know the microwave oven combo repair part you need, you can browse the list of all parts on the 57-2709-00-07, or you can search by name or part description. You can also find your part by where it is located on the 57-2709-00-07 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your microwave oven combo. We’ve also included any installation videos we have for 57-2709-00-07 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$27.35

Oven Temperature Sensor

The temperature sensor detects the temperature within the oven cavity. If there is a limited amount of heat, it is not heating evenly, or the oven will not start, this might indica...

$3.44

Main Terminal Block Kit

Terminal block kits are also known as terminal boards, or terminal strips, and they are found in a wide variety of household appliances. Most often in ranges, wall ovens, and dryers. This kit attaches the power cord to the inner wiring of your appliance. If the terminal block is faulty, your appliance will not get the power it needs to operate properly. When removing the old block pay close attention to the wire placement, this will make installing your new part much easier. If you notice any of the wires or wire terminals are corroded or damaged they will also need to be replaced.

$6.40

Light Bulb

This OEM 40 watt appliance light bulb is used for some ranges, refrigerators, freezers, and microwaves. Simply locate the existing bulb, unscrew it from its socket, and replace wit...

$21.76

Light Bulb Lens

The Frigidaire light bulb lens covers the interior light bulb in an oven. No tools are necessary to replace this item. After unplugging the appliance, slide off the wire bracket to remove the existing light bulb lens. Be sure to remove all broken glass, if applicable, before installing the new lens. It is recommended to check the state of the light bulb while the lens is off. This part is made of glass. The lens is a genuine Frigidaire part, sourced directly from the manufacturer, and is sold individually.

$104.88

Bake Element

This is a 2100 watt bake element for your oven or range. The element supplies heat from the bottom of the oven to bake or cook your food. You may need to replace the bake element i...

$34.07

Rack

$50.66

BROILER PAN & INSER

$3.87

Carousel Tray Drive Bushing - 1/4" Shaft

The carousel tray drive bushing is a part that is compatible with your microwave. The most common reason for needing to replace this part is if your current one is broken. The function of this piece is to turn the glass cooking tray in your microwave. If the tray is not turning while cooking, it will cause your food to burn. This part is black, almost one square inch, and made entirely of plastic. It has a quarter-inch shaft and is half an inch high.

$33.94

Light Lens Retainer Clip

This is a light lens retainer clip and it is used in conjunction with the oven on your range. This retainer clip secures the light lens to the oven cavity. The part is made entirel...

$161.00

Broil Element

This broil element supplies heat for cooking and is located in the roof of an oven. If there is little to no heat when cooking, a damaged element, or food is taking too long to cook, these symptoms could be solved by replacing this part. Before starting this replacement, make sure to unplug your range from the power source or shut off from the house circuit breaker. You will need a Phillips screwdriver to complete this repair. This part comes in a matte black color. For safety reasons, make sure to wear gloves. Refer to the manual provided by the manufacturer.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Above 400 beeper went off & code numbers came up on read out

  • Customer: Russell from Lake Havasu, AZ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 61 of 70 people found this instruction helpful
Cut off power at fuse panel. pulled stove out from wall went behind stove removed back panels in area of sensor that I could see from the front side, inside oven. Located sensor from rear & unpluged senser from wiring bundle reached inside oven & removed screws from sensor. Pulled sensor out & threaded wire through hole. Took old & new sensors to bench in... read more

Cord was not tightened enough by delivery crew.

  • Customer: Timothy from Spring Valley, AL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 60 of 100 people found this instruction helpful
PF alarm appeared on display. Noticed clicking when cord was moved. Had arced for some time and melted original block. New part slightly different. Only has 3 lugs, old one had six. Stack using washers provided. Take note of colors before disassembly. Use caution while working through access opening. The edges are sharp. Only tools needed are phillips screw... read more

Element showed a hot spot prior to failing open.

  • Customer: James from Delaware, OH
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 24 of 26 people found this instruction helpful
Replaced element. Removed shelves, removed two screws and lifted/wiggles old element out to pull wires off at connectors. Reversed process installing new element and truned on to test/burn off "newness" Done! read more