Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 4YED22PQFN02

4YED22PQFN02 Whirlpool Refrigerator - Overview

Get Parts and Repair Help for 4YED22PQFN02

If you know the refrigerator repair part you need, you can browse the list of all parts on the 4YED22PQFN02, or you can search by name or part description. You can also find your part by where it is located on the 4YED22PQFN02 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for 4YED22PQFN02 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$29.24

Door Bin

This door shelf bin may also be known as a refrigerator door bin, or simply as a bucket, and is compatible with your refrigerator. This piece is sold individually and is white in c...

$5.48

Lower Door Closing Cam

The lower door closing cam is designed for use with refrigerators. It can be used on either the fresh food side, or the freezer side. It helps raise the door into position so the door can seal properly when closed. It also allows the door to easily swing open and closed. This cam is made out of plastic, so it might crack or wear down over time. If your door will not open and close properly you may need to replace a door closing cam. To successfully install this part, you will need a 5/16 nut driver and a small flat blade screwdriver. Before you begin, unplug your appliance and disconnect the water supply. This replacement part is sold individually.

$57.42

Meat Pan with Handle

This clear convertible meat drawer can be used to store meats or vegetables. It has its own cold air duct to allow cold air from the freezer to flow into the drawer. You could have...

$4.73

Door Cam - Black

The lower door cam is also known as the closing cam or door closer cam and can be found on your refrigerator or freezer door. The purpose of the lower door cam is to lift the door to keep it from closing on the refrigerator/freezer liner. To do this repair you will need a 5/6 nut driver, a 5/16 socket and ratchet. For safety purposes, do not forget to turn off your appliance before making this repair. Note that this piece is black, and as per the manufacturer requires a new screw to mount the door cam which is sold individually.

$13.30

Control Bracket

This is a control bracket for your refrigerator, and may also be known as the dispenser control bracket. The function of this part is to be used as a fastener to hold the micro swi...

$8.84

Ice Guide

This is a refrigerator ice guide that is made entirely of clear plastic. This ice guide is located in the freezer door. Turn your refrigerator ice dispenser off before replacing the part. This is a simple repair, and the only tool you will need is a small flat blade screwdriver to push on the pivot tab on the bottom of the ice guide. Do not worry about breaking side or pivot tabs on your existing ice guide because it will be discarded anyway. This is a genuine manufacturer replacement part.

$63.34

Crisper Pan

This is a crisper pan for your refrigerator. It keeps your fruits and vegetables fresh by holding them in a level humidity environment that has a controlled temperature. This model...

$23.78

Bi-Metal Defrost Thermostat

If you have ice building up in your freezer, or if your freezer is getting too warm during the defrost cycle you may need to replace the bi-metal defrost thermostat. The function of the defrost bi-metal thermostat is to clip onto the evaporator and protect your evaporator from overheating during the defrost cycle. If your refrigerator does not defrost properly you can test both the thermostat and the heater to figure out which part is at fault. For this repair, you will need a Phillips screwdriver, a 1/4 inch nut driver, a flat blade screwdriver, a pair of wire strippers, a roll of electrical tape, and a few butt splice connectors.

$55.13

Ice Door Kit

In this kit you will find the support, the ice door, spring, and delay. The heater ribbon is no longer needed and therefore will not be included with this part. This kit works in t...

$63.28

Thermostat Assembly

This thermostat assembly is used in refrigerator units and freezers as a sensor. The thermostat senses the temperature increase in the evaporator during the cycle of defrosting and turns off when ice is melted. If you have any of the following symptoms, replacing your appliance could solve the problem: fridge does not start, is too warm, too cold, runs too long, or will not start. The tools needed for this repair project is a putty knife, Phillips and flat blade screw driver, 1/4 inch nut driver, and needle nose pliers. Remember to unplug refrigerator from power source as a safety precaution. Refer to the manual provided by the manufacturer for further installation instructions.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Front Door Ice Wouldn't Work And Air Going Into Freezer

  • Customer: BILL from BATESVILLE, MS
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 456 of 532 people found this instruction helpful
Thanks to the pictorial diagram, I was able to order correct parts. It was just a matter of removal of broken parts and replacing them. Ice maker now working and air is no longer getting into freezer which was freezing up ice maker. Thanks for timely delivery, now I am able to use ice dispenser, which I haven't used for long time. Thanks read more

Door Bins Broke

  • Customer: Eric from Hamburg, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 386 of 390 people found this instruction helpful
Like always your products were ordered and came extremely fast. The installation was quick. No tools needed this time. Now we have 3 door bins where we had two broken ones. Our refrigerator is more organized than ever. Thanks again! read more

Refigerator door was not closing all the way if not pushed shut.

  • Customer: Norbert from Sugar Land, TX
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 289 of 295 people found this instruction helpful
Remove the top hinge cover. Removed the top hinge support. Lifted the door from the bottom support. Old door cams were worn completly flat. Replaced the lower door cam and closing cam use a little vasalene for lubricant on the cam surfaces. Placed the door back on the lower hinge support. Replaced the top hinge support. Door is closing great now. read more