Models > 4YED22PQFN01

4YED22PQFN01 Whirlpool Refrigerator - Overview

Get Parts and Repair Help for 4YED22PQFN01

If you know the refrigerator repair part you need, you can browse the list of all parts on the 4YED22PQFN01, or you can search by name or part description. You can also find your part by where it is located on the 4YED22PQFN01 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for 4YED22PQFN01 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

$3.76

Lower Door Closing Cam

This door closing cam is located on the bottom of the fridge/freezer.

$3.84

Door Cam

Note: As per manufacture a new screw is needed to mount door cam. Sold individually.

$53.86

Meat Pan with Handle

$8.38

Control Bracket

This bracket holds the micro switches and the light in the freezer dispenser section.

$59.77

Crisper Pan

$8.56

Ice Guide

This ice guide is located in the freezer door.

$50.59

Ice Door Kit

This kit includes the ice door, support, spring and delay. The heater ribbon is no longer attached - the heater is no longer needed.

$57.82

Thermostat Assembly

The thermostat will sense the temperature increase in the evaporator during the defrost cycle and will cycle the defrost heater off after the ice or frost is melted.

$23.19

Ice Bin Auger Drum

This white ice bin auger drum comes with a washer.

$27.87

Bi-Metal Defrost Thermostat

If ice is building up in your freezer or if your freezer is getting too warm on the defrost cycle you may need to replace the bi-metal thermostat.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

front door ice wouldn't work and air going into freezer

  • Customer: BILL from BATESVILLE MS
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 235 of 283 people found this instruction helpful
THANKS TO THE PICTORIAL DIAGRAM, I WAS ABLE TO ORDER CORRECT PARTS. IT WAS JUST A MATTER OF REMOVAL OF BROKEN PARTS AND REPLACING THEM. ICE MAKER NOW WORKING AND AIR IS NO LONGER GETTING INTO FREEZER WHICH WAS FREEZING UP ICE MAKER. THANKS FOR TIMELY DELIVERY, NOW I AM ABLE TO USE ICE DISPENSER, WHICH I HAVEN'T USED FOR LONG TIME. THANKS read more

inconsistent compressor and condensor fan operation

  • Customer: Steve earney from Brooks GA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 130 of 133 people found this instruction helpful
Compressor start relay would cycle several times before compressor would come on. Replaced start relay and defrost timer assy. Operated more consistently however not completely reliable. Ice would begin to melt. Noticed that if you would cycle the temperature control the compressor would start again and operate for several hours then not cycle again. Jum... read more

Refigerator door was not closing all the way if not pushed shut.

  • Customer: Norbert from Sugar Land TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 122 of 125 people found this instruction helpful
Remove the top hinge cover. Removed the top hinge support. Lifted the door from the bottom support. Old door cams were worn completly flat. Replaced the lower door cam and closing cam use a little vasalene for lubricant on the cam surfaces. Placed the door back on the lower hinge support. Replaced the top hinge support. Door is closing great now. read more