Models > 4YED20PKBW00

4YED20PKBW00 Whirlpool Refrigerator - Overview

Get Parts and Repair Help for 4YED20PKBW00

If you know the refrigerator repair part you need, you can browse the list of all parts on the 4YED20PKBW00, or you can search by name or part description. You can also find your part by where it is located on the 4YED20PKBW00 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for 4YED20PKBW00 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

$3.82

Door Cam

Note: As per manufacture a new screw is needed to mount door cam. Sold individually.

$56.69

Thermostat Assembly

The thermostat will sense the temperature increase in the evaporator during the defrost cycle and will cycle the defrost heater off after the ice or frost is melted.

$27.33

Bi-Metal Defrost Thermostat

If ice is building up in your freezer or if your freezer is getting too warm on the defrost cycle you may need to replace the bi-metal thermostat.

$10.86

Door Closing Cam Kit

This door closing cam kit is intended for use with the bottom of refrigerator and freezer door hinges. The cam helps with the closing of the doors and to keep them slightly in position when opened.

$3.37

Door Shelf End Cap Kit

This door shelf end cap kit contains two white end caps, two adhesive strips, and an instructions sheet. Each end cap can be used as either for the left side or the right side.

$2.70

Screw

This screw is sold individually.

$3.76

Shelf Support Stud

Sold individually.

$20.61

Shelf Support Stud

This is a 12 piece kit.

$11.34

Shelf Support Stud - White

This kit contains two options - One that is a push and turn and the other that is a screw in.

$15.67

TRAY-EVAPORATOR

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

inconsistent compressor and condensor fan operation

  • Customer: Steve earney from Brooks GA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 137 of 140 people found this instruction helpful
Compressor start relay would cycle several times before compressor would come on. Replaced start relay and defrost timer assy. Operated more consistently however not completely reliable. Ice would begin to melt. Noticed that if you would cycle the temperature control the compressor would start again and operate for several hours then not cycle again. Jum... read more

The door would not close properly. The CAM had broken.

  • Customer: Thomas from San Clemente CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 92 of 94 people found this instruction helpful
The repair was very simple.

1. Remove the food from the door shelves.

2.Remove the door by first removing the three screws holding the hinge at the top of the refrigerator.

3. Lift door off of the bottom hinge.

4.Replace bottom CAM on bottom hinge (one screw)

5. Replace top CAM and shim on door (one scre... read more

Fridge was getting too warm, ice buildup on coils.

  • Customer: Cathy from Winter Park FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 79 of 87 people found this instruction helpful
WARNING: REPLACING THIS PART REQUIRES CUTTING AND SPLICING ELECTRICAL WIRES. RISK OF ELECTRICAL SHOCK OR FIRE. DO NOT ATTEMPT THIS REPAIR IF YOU ARE NOT EXPERIENCED WITH ELECTRICAL WIRING.

Part Info:
The bi-metal strip is clipped onto the evaporator coils and is designed to regulate the defrost coil temperature. If it is not functioning prope... read more