Models > 4KV25H0XWH5 > Instructions

4KV25H0XWH5 KitchenAid Mixer - Instructions

All installation instructions for 4KV25H0XWH5 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the mixer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 4KV25H0XWH5
1-15 of 101
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

wouldnt turn beaters

  • Customer: Barry from Rowland Heights CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 29 of 30 people found this instruction helpful
removed metal strap around motor housing then remove the 4 screws holding top motor cover on, then removed the 4 screws that hold gear cover in place, remove long gear that is driven by the motor gear, then with ring pliers remove ring off long drive shaft and lift off worm gears. once all gears are removed --removed all the old grease ( do this to get all the metal shavings out from the failed gear) repace the grease in the gear housing and reassemble in reverse order

Plastic gear housing in stand mixer fractured causing gears to crash

  • Customer: WES from BREVARD NC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 32 of 39 people found this instruction helpful
Removed four screws to remove main cover. Removed four more screws to remove fractured plastic gear housing cover. Removed retainer ring and slid two gears and dowel off main shaft. Lifted out remaining gear train and bearings, Removed all grease and metal chips from all components. Greased new gears and reassembled. Replaced plastic gear housing cover with oreviously purchased die cast replacement part. Assembled main cover.

MIXER MADE VERY BAD GRINDING NOISE, AND WOULD SKIP WHILE MAKING BREAD DOUGH

  • Customer: Dennis from Lake Mills WI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 22 of 25 people found this instruction helpful
1, REMOVED TRIM PIECE (1 SCREW)
2, REMOVED COVER (4 SCREWS)
3, REMOVED SPEED SWITCH ASSEMBLY (2
SCREWS)
4, REMOVED GEAR COVER (4 SCREWS)
5, REMOVED AND EXAMINED 2 WORM GEARS FOR WEAR. GEAR COVER WAS BADLY CRACKED, DON"T KNOW IF IT WAS CAUSED BY A PREVIOUS REPAIR OR BY HEAT, AS OLD COVER IS PLASTIC.
RECEIVED NEW PARTS AND INSTALLED THEM,
2 BEARINGS, 2 WORM GEARS, 1 NEW COVER OF DIECAST METAL AND A NEW GASKET.
ALL REPAIRS MADE WITH A #2 PHILLIPS SCREW DRIVER.
MY WIFE THEN MADE BREAD, AND IT PREFORMED FLAWLESSLY.

Kitchenaid stand mixer would get stuck (stripped gear)

  • Customer: Lucy from El Dorado Hills CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 19 of 24 people found this instruction helpful
First I removed the screws that hold the silver band and the top of the mixer (cover). I removed the cover. I then removed the 4 screws that hold the gear housing and removed the housing. I removed the worm gear and removed the bearings and the washer from the "old" worm gear and put them on the replacement worm gear. I took gear grease from the cracked housing and packed the replacement gear with this grease. I attached the gasket to the replacement housing. I placed the attachment gear into the replacement housing and placed the housing over the gear assembly. I then put the mixer back together and ran it for a few minutes to dispurse the gear grease. I just mixed up some bread dough and everything seems to be in working order. I have never done this before so I hope it will continue to function properly.

Mixer speed was uncontrollable

  • Customer: James from Villa Rica GA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 16 of 17 people found this instruction helpful
Removed screw from back of mixer cover band and then removed the 4 side screws, lifted top off of mixer and removed screws from circuit board control switch, removing wires one at a time so as to install correctly. replaced screws in circuit board/control. Restored top of mixer replaced screws and the put cover band back on mixer.walla done

Gears Stripped on Stand Mixer

  • Customer: Gary from Plano TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 14 of 14 people found this instruction helpful
Bought a KitchenAid Pro Series stand mixer from Sam's Club about five years ago. The transmission gears stripped. It is failry easy to replace but you need to replace the worm gear and the pinion at the same time. Make sure all the old grease is removed completely to ensure no old shavings reaming in the transmission housing. Also, if you have a fiberglass transmission housing, inspect the housing closely to indetify any hairline fractures and do not fill the transmission assembly with too much grease becasue you need room for the housing to breathe when the unit is in operation. If you fill the housing too much and tighten it, it "WILL" crack the housing. You want enough gree to keep the asssemnly lubricated but not too much that when you run the mixer that it expands and cracks the housing.

Kitchenaid Professional Stand Mixer would rev up quickly and stop working after a few seconds.

  • Customer: Jeremy from Aurora IL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 10 of 17 people found this instruction helpful
I read several stories online explaining that this was a problem with a speed sensor. In order to change the part I removed the motor cover (required removing 3 or 4 screws) and simply unplugged the old sensor from the speed control board and plugged the new one in. Took very little time and minimal effort. Mixer now runs like it did when it was new and cost much less than replacing the entire appliance.

I stripped two gears to the power take-off at the head of the mixer using the meat grinder attachment.

  • Customer: Raymond from Monterey CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 6 of 6 people found this instruction helpful
I investigated the problem by opening the mixer (four screws) and examining the gear box. Two gears were stripped. I ordered them, using the parts diagram provided. They arrives in about two days. I disassembled the gear box, cleaning out all grease and inspected for further damage. The gears and housing were completely cleaned with solvent. The transmission was then reassembled and regreased with food-grade grease. The mixer is now reassembled and working well. I was very pleased with the price and simplicity of my repair, versus taking it to a repair shop.

Plastic gear housing breaking

  • Customer: Bret from Centennial CO
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 6 of 6 people found this instruction helpful
Very happy to find that the new gear housing was metal, not plastic. The whole problem was poor design of plastic to hold metal gears. Removed housing held down by four screws, removed two gears that were damaged. Retaining ring was difficult to remove from retaining slot. New gears replaced the old ones, new retaining ring put in place, new grease packed into all gearing, new stronger metal housing put in place and the Kitchenaid industrial mixer is better than new. Very happy with the parts I purchased.

Worm gear stripped.

  • Customer: Stephen from Colorado Springs CO
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 6 of 8 people found this instruction helpful
Removed mixer motor housing by removing 5 obvious screws.
Removed plastic transmission cover by removing 4 obvious screws.
Down load parts exploded drawing from PartSelect.com
Found the worn part by the shiny teeth on the large gear.
Found the large worm gear on the drawing and ordered the gear, and associated bearings. Did not need the seal.
Removed worn part, assembled new gear and beargings in same manner as the worn part, and placed new part in mixer.
Replaced transmission cover gasket.
Repacked grease from transmission cover onto the new gear.
Replaced transmission cover (4 screws).
Replaced mixer motor housing (4 screws).
Replaced mixer trim band around the motor houseing joing. (1 screw).
Plugged it and and it works, good as new.

when turned on mixer went full speed for 10 secs. then shut off. when turned off then this repeated. Trouble guide indicates defective speed control.

  • Customer: jerry from farmland IN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 5 of 5 people found this instruction helpful
per e.g. and put cover on and secured screws. Pluged in unit turned it on and it worked for 25 secs then went full speed and shut down.. repeat this several times got same results. Put old unit back in and it worked for 2 days then same results. I now suspect coil on shaft is defective. I'll order that and see. Unless some one knows of another problem.

broken thumb screw

  • Customer: Kathleen from Silvis IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 6 of 8 people found this instruction helpful
remove the old screw and screwed the new part in place. I like your link because it shows a picture of the fixture and you can find the part you need real easy. Will order from you again when I need it.

speed surged after mixer warmed up

  • Customer: Thomas from Christiana TN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 5 of 6 people found this instruction helpful
Took off cover, marked leads, unscrewed two screws and replaced circuit board (speed swith unit). This one was really easy.

No beater rotation (stops in one place)

  • Customer: Ken from Spicewood TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 5 of 6 people found this instruction helpful
Remove the top cover. Loosen the circuit board and remove the gear case. Remove the retaining clip on the gear shaft and remove the gears. Clean the old grease out and relube. reassemble in reverse order . Not a bad job at all.

Stripped gear teeth

  • Customer: Roger H. from Polo IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 4 of 4 people found this instruction helpful
Removed rear band screw and band
remove 4 screws from head assembly and remove mixer head
remove 2 screws fastening speed control switch
remove 4 screws from gear box cover
remove cover and slide out bevel gear and replace
remove retainer ring and slide gear off shaft.
reassemble in reverse order, apply grease to gear teeth.
first time 25 minutes to inspect and reassemble
2nd time 5 minutes to teardown,replace parts, and reassemble
All manufactured assemblies should be this nice to work on.
All Instructions for the 4KV25H0XWH5
1-15 of 101