4KSRS27QFW01 KitchenAid Refrigerator - Instructions

remove contents of door-----------hardest part of chore remove top hinge cover remove three top hinge screws remove door and lay on table remove two screws holding black plastic cam piece in door, remove black plastic piece (slightly held in by some type of mastic) just pull till it comes our insert new piece, insert two screws lubricate parts mount door on hinge pin insert tip hinge pin and plate and fasten with three screws attach cover............reload refrigerator door taking opportunity to throw out old bottles and mystery jars Finis

Should have. . . . Just taken the ice maker out in the first place . . . . When I saw no ice I assumed the timer was bad. . . Replaced it. . Then when that didn't fix it again assumed that water valve was bad. . . . Replace that also to no avail. . . . Finally took out the ice maker and saw that the heater had stopped working cuz there was still ice stuck in it. . Replaced ice maker. . . All good. . . The water valve I replaced was a good thing cuz you can definatley tell the difference. . . . Anyway. . . Fixed!

Looked on YouTube and found the PartSelect video. Viewed the video and replaced the part.

Online I learned how to diagnose the problem and order the part I needed. Replacement was simple and now we have ice. It works perfect, no adjustments needed.

Removed front bearing(nut) assembled parts in correct order, the second time, attached bin front cover and all was good. Wife is happy again.

Very easy to replace. Disconnect water line. remove 2 screws pull out filler tube. replace with new one.

Spent six hours melting the ice berg, twenty minutes cleaning things up and ten minutes replacing the ice maker. The video was great the only piece of information that was missing was a statement that it may that several hours for ice to be produced. Thanks for the prompt and courteous support during ordering, a good product and support video.

1. Remove the ice-maker/water dispenser cover plate located on the freezer door, by: inserting a putty knife blade at the bottom and freeing up the two retainer tabs; then pushing up. (note: be careful pulling the cover plate, there are many electrical connections on the back).

2. Note the electrical connections on the back of the cover plate and locate the connect close to the inside of the freezer door and disconnect it. (Note: this is much easier than pulling each wire off its connection point and then having to remember which color coded wire went where).

3. Carefully work the door hinge pin back out to the right and remove it and the hinge (Note: in my case the pin was already half way out so the old door couldn't close - and since this model door had a heater which came on because the door was misaligned there was constant flow of warm upwards causing ice to melt, run down and re freeze thus making the door difficult to open).

4. Unscrew the single her head screw holding the small metal piece to the right that retains the know upon which the outer door frame turns. Move the frame to the right to free it and work it out if the way. You now have access to the ice-maker door and hinge pin assy.

Did it entirely by myself while my husband was at work

removed the old ice maker, removed the cable from the old as none of the ones included were correct, and attached it to the new. within in two hours it was making ice.

Followed the online video instruction. Super easy

Took off all screws on box.Removed front of drawer,removed back-up to drawer and auger as one unit. Removed C-clamp on end of auger,this released all the parts. The end of the auger shaft unscrews, remove broken piece and reverse process with new part

Repair went just like the video. Since refrigerator and freezer are side-by-side, it's a little harder to get to the screws. This is where the small mirror comes in handy.

I had to take the icemaker cover door off to get the icemaker in. Then I realized I needed to use the additional brackets.

I found exact instructions on Youtube. Watched the video. Verified that my Control Bracket was in fact broken by partial disassembly. Ordered the part from PartSeclect. Received the part the next day (though I only paid for ground/standard delivery). Installed the part as described in the video using only two screwdrivers and needlenosed pliers within 14 minutes from start to dispensing water again. My water dispensing was interrupted less than 48 hours. Amazing!!! Thank you. It was fun, fun, fun.PaPa43