4KSRS27QFA01 KitchenAid Refrigerator - Instructions

The repair was incredibly easy -
1. Turn off the water at the water line for the fridge
2. Disconnect the pressure fittings for both lines running to the resevoir.
3. Remove the old resevoir
4. Install the new resevoir and run the lines back to the orginal fittings.
5. Reconnect the fittings, turn on water.
6. Drink water!

First remove the ice container from the freezer
and dump all of the ice. Remove the four
screws holding the front ice container cover. Remove the control arm screw and bracket from the bottom of the ice container, remove crusher housing (screws and retainer clip). Remove nylon
bearing nut on front of auger shaft (left handed threads). Remove crusher blades and spacers (remember order of blades and spacers). Remove broken floating baffle. Replace baffle and reverse removal procedures.

the parts sent included two replacement kits which at first was confusing. I determined that I only needed the one with the black tubing for my Kenmore refrig. Turned off water supply and vacuumed up all the dust bunnys behind refrig. Removed bottom grate on refrig where black tubing attaches at the other end. Released water left in tubing at dispenser. I did not have to remove the front panel. Removed one screw attaching the nozzle to the dispenser. Decoupled tubing at the far end, more water came out here too. Pulled out upper end of tubing a couple of inches and snipped off. Attached tubing to new tubing with thin wire (as others here recommended) and had my husband pull at far end while I pushed slowly at the dispenser end. Once through reattached screw at top and recoupled at the bottom. Mission accomplished!

Ice Maker would seem like it was the valve was leaking and Ice would build up at the rear of tray.
After listening to it cycle, (drop ice and fill) valve would open up again about 20 minutes later.
Over flowed and iceberg would form at rear.
Replaced icemaker unit and works fine now.

The hardest part was getting the front cover plate off. I used two kitchen knifes one in each slot on the bottom of the plate and pried it off and unplug it. I removed one screw to release arm. I then used long nose pliers to remove the pin on door arm assemble. Then unplug door heater. New door has no heater. The heater had cooked the plastic arm, which caused the arm to fail. Then reassemble in reverse order.

Followed instructions supplied. It was relatively easy and the parts fit exactly right. Sears wanted twice as much for the part and service would have charged me another $100 to come to my home. I saved over $100 doing the project myself.

I first removed the ice bin from freezer. There were four nut screws on back of ice bin cover that I removed with a screw driver, giving me access to the deflector. The deflector has two prongs that attach it securely to the ice bin, I used a phylips head screw driver to release the prongs from the deflector. I installed the new deflector by placing it through the bottom portion of deflector area, using the phyllips screw driver I engaged the prongs of the deflector into slots on ice bin. There was a hook on the back side of the deflector that went over a metal rod that controls the ice cube release. Then replace front cover of ice bin with the four nut screws and returned it to the ice maker location.

Removed face plate, disconnected wires, removed and replaced micro switch and control bracket.

First, turn of the water supply. Then remove the snap on grill from the bottom front of the refrigerator. Disconnect the black hose from the white hose and drain the hoses into a suitable recepticle. Then remove the 1/4" screw that holds the nozzle in place. Cut the hose off just behind the nozzle bracket and tape the end of the new hose to the now exposed end of the existing hose. From the bottom of the door you can now gently pull out the old hose while pulling in the new one. Re-attach the new hose to the existing white hose and replace the 1/4' screw to the new nozzle bracket. I reccoment using 1" wide tape and only going around the tubes once. Too much tape and you won't be able to feed it through the small hole at the bottom of the door. Have someone feed the hose from the top as you gently pull from the bottom.

I replaced the control bracket, which has mounts for the switches used to activate the ice and water dispensers. The water switch mount was broken, so the switch would not activate. It was great that I could find this part (the control bracket) on PartSelect's site.

If the person doing the repair has a little patience, then he/she will be rewarded!:

The first step is to pry off the front panel: I pried off the panel at the bottom. It will pop off, but takes a little effort. I used a couple of screwdrivers to pull it up at a couple of spots at the same time. Once the bottom pops out, then I pulled straight up on the panel. (If you try to pop out the panel at the top, you will damage it, so make sure to pop it out at the bottom.)

Next, disconnect the wiring that goes to the panel, and put the panel aside.

I then took a digital picture of the arrangement of wires and switches on the control bracket.

I disconnected any wires going from the inner part of the refrigerator to the control bracket, and then unscrewed the control bracket.

After removing the old control bracket, I carefully noted how the two switches (one for ice, one for water) mount into it. I removed these switches and put them into the new control bracket.

I then remounted the control bracket into the refrigerator, screwing it into place. I used the digital picture that I had taken earlier to make sure that I knew how to reconnect all of the wires.

I plugged the the remaining wires to the front panel, and then snapped the front panel back into place on the refrigerator door.

I was done!

Remove the cover plate from the bottom. Use care and patience when performing this step. It takes longer to remove the cover plate than replacing all of the parts involved. Slide off each switch, unplug electrical connectors and trust me when I tell you that you can figure out the rest. E Z, E Z, E Z!!!!!

1. shutoff water
2. removed 3 screws holding old ice maker. A small nut or screw driver is needed to get into a somewhat tight area
3. detached electrical connector
4. cut indicated area for water inlet to lie in
4. attached new electrical connector (no splicing needed)
5. attached new ice maker with 3 screws
6. put on water

my order was processed and received withn 3 days. Replacing the parts on my kitchenaid refrigerator was straight forward, since the design was made for quick removal for cleaning of parts, with no tools required.
My only recomendation to KitchenAid would be possibly design the weak points a little stronger so they do not break in the first place.

Removed the top two screws and one on the bottom which attach the ice maker to the side of the freezer. I unclipped the wire bundle from the side of the ice maker and unplugged the connector, totally removing the unit . The maker came with several different wiring setups, but I just used the existing. The contol arm on the new unit basically snaps into place and the above process is reversed to install the new unit. My old ice maker had an accelerator which blows cold air to the bottom of the tray to speed up ice production. This component was undamaged and by taking off the new units outer end cap and borrowing the clips from the old unit, this component can be installed on the new ice maker.

I removed the screws on the upper hinge and removed the door. I removed the lower cam in about 2 minutes and had it replaced. The upper cam was a tight fit in the door and I resorted to vise-grips to remove it. Total time to replace cams and put the door back on was 30 minutes. This saved me $100.
Thanks