4KSRS27QDW01 KitchenAid Refrigerator - Instructions

Removed the two lower drawers and crisper frames as would normally be done to clean. After cleaning, replaced as normally would substituting the broken frame with the replacement. If I hadn't cleaned them and only replaced, it wouldn't have taken more than three minutes.

I shut the unit off for about ten hours and when I turned it back on and set the temperatures for the freezer and refrigerator it has been working great.I will keep the part in case it happens again.

watched the installation video twice and took my time to make sure all parts were put back together in the right order

replaced cam, new one broke after opening door 3 times...

Removed front bearing(nut) assembled parts in correct order, the second time, attached bin front cover and all was good. Wife is happy again.

Very easy to replace. Disconnect water line. remove 2 screws pull out filler tube. replace with new one.

A You Tube video described the repair steps and by following these instructions the whole process worked seamlessly.

This is a simple repair. the only reason it took as look as it did was because you need to empty the products from the door(s). Of course this is a good opportunity to thoroughly clean the fridge. The problem was caused by wear on the plastic spacer for the bottom hinge. Remove the plastic covers that conceal the top hinge located on top of the refrigerator. Remove the three bolts that attach the hinge to the housing. The door can then be lifted off the bottom hinge. Remove and replace the bottom spacer. Then remove and replace the receiver in the door by prying it out with a screwdriver or pliers and popping in the new one. I put a dab of lithium grease on the hinges before I reassembled them to reduce the wear and extend the life a little. Reverse the procedure to reassemble.

The video on the site made the repair extremely easy. It took 15 - 30 minutes start to finish. Had it not been for the video I wouldn't have known that the plastic nut on the end of the auger was reverse threaded. I would highly recommend this site for ordering appliance parts.

I have a KitchenAid side-by-side refrigerator and the right door clunked everytime it opened. We think it was damaged when contractors had to move the fridge and probably were too rough with it. I went on line and found that I could actually repair it myself (thanks to this web site, a great web site, by the way). I researched and found out through others that I needed a new door closing CAM kit. I only needed to fix 1 door, but bought the whole kit anyway (PS358690, Door Closing Cam Kit)to have spares. The kit showed up, I followed the great instructions via the video to remove the door, replaced the upper CAM on the door first and then ran into a snafu with the lower cam. The hinge on my model fridge does not have a replaceable CAM, it is physically attached to the door hinge. The instructions that came with the kit showed a hinge that was not my hinge - sigh. I had to put back all the old clunky parts, put the door back on and go order a new hinge (hopefully). Luckily there was a hinge available for my model with the CAM installed. I purchased it (PS331817, Door Hinge with Cam) and it came quickly like the other parts. I took the door off again (I knew how to do it this time), I replaced the hinge with ease, put the door back on and it is no CLUNK-FREE - Smooth like when we bought it. Thanks to everyone who wrote in about their clunking issues and thanks to PartSelect for the parts and the help.

I would not have attempted the repairs without your instruction. I use a Drimel tool with a abravise blade to cut the part off the shaft. After I realized the Drimel tool would work. It took me parhaps 10 minutes to get it off the shaft. I had already ordered the new part and the job was complete. Thanks for the help. Ron Burch

Went as planned. Video was such a great help. Delivery was in world record time. Price was right. Will use you again.

Watched video of repair. Took all drawers and drawer holders out of freezer to acesss back panel. Removed 6 screws from back panel,slid up and out. Cut 2 wires to remove old bi-mtl defroster. splice the wires and attached new bi-metal def.

Using instructions found on the internet and the illustrated parts breakdown it was just a matter of following instructions.

I wasnt about to call Mr Appliance of Bayport NY the last time I called him I got a bill for $72.00 and he told me I needed a new frig. So I paid him then the next day I went to parts select and fixed it myself for about $50.00 But this time it was my Moms frig and the frig side (fresh food side) wasnt getting cold So again I went to parts select and put in a bimetel thermostat and it works perfect now. Im sure I saved a lot of $ and thanks to parts select, They helped me diagnose the problem and make the repair step by step! EASY! Thanks parts select...Garry from long island NY