4KSRS27QAW00 KitchenAid Refrigerator - Instructions

The fix was easy. I jacked up the unit and put on blocks. I used socket and ratchet removed the wheels. Reinstall new ones and let off the blocks.

I watched the video a few times and pretty much did as it said to do. Took about 20 minutes start to finish. It seems to be working 100%.

I found the part I needed at parts select and followed the video on their web site. They have a very informative web site, it made my job easy. I highly recommend this company.

Using a pair of pliers position the nose perpendicular to the inner wall of the ref and grip tight on the flat part of the support stud and twist counterclockwise until it become loose. Once loosened pull the support stud outward until it clears the the hole. Installation: Slide the support stud in and twist it hand tight. Using a vise grip and locking the jaw just tight enough to hold it firm on the flat parallel edges twist them (one at time) clockwise until it feels tight the tongues are parallel to to be able to slide the shelf support.

Top left mounted Icemaker facing front. Disconnect power to fridge. Using 1/4" nut driver remove single silver nut under right rear side. It holds a plastic cover over the electrical connection, unhook the cover and remove it. Release clips under front lip under both sides and entire icemaker will slip and twist out. Remove electrical connection to ice tray. Place assembly on bench and remove 3- 1/4 hex screws from under side to release bottom tray. Snap cover off motor and remove. Carefully align pin and arm on control assembly to ice tray and-re assemble. May take 30 min to dispense. Discard till clear.

I took ice bin apart to ensure what part I needed. Got Serial # & Model # from inside fridge. Online search for Whirlpool Parts to check out prices. Settled on PartSelect for best price. Quick service too!!! Before putting it all back together, I reviewed the video. It was pretty good. Just left it up & after each couple of steps, I'd look at what was next. Went together with no problem. There could have been more details given, like ensuring that certain things lined up during reassembly. There was dead time when the narrator could have given pointers.

Removed the two lower drawers and crisper frames as would normally be done to clean. After cleaning, replaced as normally would substituting the broken frame with the replacement. If I hadn't cleaned them and only replaced, it wouldn't have taken more than three minutes.

I shut the unit off for about ten hours and when I turned it back on and set the temperatures for the freezer and refrigerator it has been working great.I will keep the part in case it happens again.

watched the installation video twice and took my time to make sure all parts were put back together in the right order

replaced cam, new one broke after opening door 3 times...

1. Unplug the electric plug. 2 Either be in a well lighted place or get a flashlite. 3. Remove all food from top shelf. 4. Remove the knobs from both controls by pulling on them or use pliers to grab the center and pull. 5. Use the thin bladed knife and gently slip the knife under the thin plastic panel that covers the two controls and pop it off. 6.Go in back of the control panel and remove the two hex headed screws that holds the panel onto the roof of the refrigerator.7. Locate the right hand control, and use a philips screw driver to remove two philips screws that hold the temperature control body in place. and remove the wires from the terminals by pulling them with a long nose pliers.8. Locate the white panels that cover the thermostat sensor and remove the screws holding them onto the frig body. slip the long thin tube out of the plastic piece it is formed to fit.9.Draw on paper the shape and measure the deminsions,of the long thin tube. Straighten out the tube and remove the plastic covering it. Now slip that tubing over the new piece.10. Form the tubing into the odd shaped holder and gently place all of the new asssembly against the frig wall and cover with the two white panels that you removed to get to the long sensor tube. 11. Reassemble the controls in the same order you took it apart. Plug the frig back in to the electricity and set the control on 5 and it should run. Watch for a period to hear the unit cycle on and off. You are a genius and have saved at least 150 dollars.

Removed front bearing(nut) assembled parts in correct order, the second time, attached bin front cover and all was good. Wife is happy again.

When my thermostat was shipped the email contained a step by step video. I just watched the video and installed it.

un-plug the power cord. remove both control knobs. pry off the cover. remove 1 screw on the right and left with the nut driver. remove two screws in back with the nut driver. remove the screw holding thermostat in place, loosen screw holding the left side of the l plate. lift thermostat up and remove two nut driver screws. remove the temperature sensing line from holding device. Remove cover down the side of refrigerator and the cover over the sensor (in back corner) carefully remove the sensor line. Carefully bend the sensor tube into the shape of the removed part(do not kink)install the new part in the reverse order of removing.. Use flat blade screw driver to press sensor line into the snaps. This was one of the easiest repairs I have ever completed.

Simply done !