4KSRS25QFW00 KitchenAid Refrigerator - Instructions

I unplugged the refrigerator then I took the bottom screw out of the ice maker. I loosen the other two screws and picked up on the ice maker and it came out. I saw that the top of the ice maker where the screws are they sit in a groove so you dont have to take the top screws out just loosen them and pick up on the ice maker and it will come out. Then I unplugged it from the old ice maker not from the wall of the refrigerator. The reason is I didnt want to mess up the cover that hides the plug in the wall of the refrigerator. Then I took the metal on and off bar off the old ice maker and put it on the new one. Then I took the face off the new ice maker and unplugged the new wire. All you have to do is press down on the little clip and pull back on the plug. Then I plugged the old plug into the new ice maker. Then I set the ice maker in the grooves on the top screws then iput the bottom screw back in then I tighten all screws. I plugged the refrigerator in. I started getting ice in thirty minutes. My wife think I can fix anything now. Thanks

Very easy to replace you can even watch a video on how to do it.

It was pretty easy, but I sure wish they had said the auger had "left" hand thread. After I watched a vid on youtube the job went very easy. The new auger works just fine. The only problem I had was the left handed thread with the plastic nut on the end of the auger. Well worth the effort now I can get ice reguulary.,All the parts fit too.

Removed the auger apparatus from the ice bin, replaced the auger drum and then reattached the auger apparatus to the bin. Cause of breakage was due to ice melting in the bin and then refreezing. Keeping the many parts in the correct order on the auger can be difficult.

Instead of trouble shooting what part was bad, just replaced the whole unit. Probably cheaper in the long run and the whole process took less than 15 minutes. Pulled the old icemaker out, plugged in the new one and back in business.

The video of the repair that was on your website was extremely helpful. It showed in detail how to replace the parts item by item. I could not have done it correctly without the video. I believe anyone could have replaced these parts with your instruction video.

noticed the auger was broken so I ordered an entire unit, however I will order auger to repair the removed tray.

remoove all the food and shelves out from the freezer section, remoove the light bulb lens ( 1 phillips screw) remoove light bulb, take out 6 srews on the back panel then slide out through the top with a slight bending curve motion, the bimetal thermostat will be clamped to the evaporator inlet, ( just after the cap tube) snap it off, then cut the wires about 2 inches from the stat, strip the ends about a quarter inch with wire strippers, same on the new stat, then use 16 or 18 gauge butt splices and crimp them , then reassemble in reverse order.

Followed instructions in video and instructions by other home owners. Installation went very well. Parts Select shipped the repair kit. A good company to do business with. Saved a lot of money by doing the repair myself.

Unplug refrigerator.loosen 2 screws,take bottom screw out.Unplug electric connector,take off ice arm,install on new ice maker.Reinstall maker.plug in refrigerator.Really easy to install!

Removed ice bucket so ice would not dispense while working on ice guide. Removed damaged ice guide by prying 2 clips with a flat-head screw driver. Installed new ice guide by pushing beyond final position, lower bottom clip into position, then snap 2 side clips into place.

I followed instructions in the video you provided. No problem at all. Took less than an hour.

Just looked at your video twice and then did it with no problems. Thanks

fisrt i watched your video loosened two screws removed one removed icemaker installed new one tightened screws had ice in 2 hours i never shut the water off no need

the online video on how to change out the part saved me tons of time and do it right.....keep those videos coming, also right part too and easy to find on your site