4KSRS22QFA01 KitchenAid Refrigerator - Instructions

After reading (Warm air getting into freezer) by David from Chesterfield, MO & (Ice door was broken) by Ray from San Antonio, TX, it was easy to follow their instructions (especially- Patience is a virtue! and go step by step. Thanks to both for their detailed instructions, this retired mechanical engineer was able to 'get it done'. Stan from Denison, TX

pulled crisper drawer out plus drawer above. Removed old bracket & replaced with new part. Put drawers back in. Part was exact fit - no modifications required. Time was actually less than 5 minutes.

removed both drawers, glass. lifted old part up and out. set in new part. replaced glass and drawers........

I watched the installation on your web site and followed your directions and it fell right into place. Absolutely no problems. Thanks.

Was surprisingly easy. Hardest part was taking the cover off the front to get access to the control bracket and switches. Can be done by prying two notches on underside of cover until they pop. Then slide up and off. Once off I could immediately tell the plastic clips on control bracket were broken. So replacing fixed that issue. My other issue was the ice dispenser door would not stay closed and sealed. I noticed that the plastic hook that holds metal dispenser pin in place was broken. Had trouble finding that part online so I superglued it in place and that has held it just fine. Now both my ice dispenser and water dispenser are working after buying a $10 part. This site is awesome. I am sure I would have paid $200 for this from a repairman.

First, removed the top hinge (3 screws), then lifted the door off the bottom hinge. Replaced the Cam on the bottom of the door and then the Cam on the bottom hinge (one screw for each). Placed the door back on the bottom hinge, reinsert the top hinge into the door and secure top hinge to the refrig with the 3 screws original removed. EASY!!

The how to video told me what to check to determine what part was probably broken. Then another video showed me how to take it apart. It gave me the name, number, and a photo of the part. I ordered it from Part Select without even checking with another retailer since they gave me the information to do it myself, saving me lots of $ for repair labor costs! Then I watched the repair video again and put it back together! It works! It was simple and I really appreciate this service! Thank You

The repair went extreamly easy and exact to detail. I followed the video step by step, and that turned the assembly into a professional job.

Remove drip pan from indoor ice dispensing system remove to bottom screws holding dispenser faceplate .lift faceplate out of the way exposing the bracket and ice and water dispenser micro switches be careful in removing microswitch, the one I removed came apart and had a little difficulty putting it back together ,used super glue and fix that problem. No instructions came with bracket so take your time. This is a relatively simple job any one should be able to do it.

I did it a bit different from instructions mainly because I disassembled it to troubleshoot before going on line to find part and "easier" instructions.I had a 5" block of wood and cut a shim to use with that to hold the door up. I got on my hands and knees with a mirror and removed the lower hinge plate then the screws holding the upper and lower cams. These both were quite worn so I just took them to my shop and with a hand grinder I rounded off the sharpo corners of the cogs of both cams and then reassemble the hinge plate and cams. This eliminated the loud clicking and the door closed easily but I was afraid it woulod not "Auto Close" when needed so I went online to find this page with the parts needed along with wonderful instructions. I ordered both upper and lower cams which came 2 days later (THANKS). I installed them my way since I did not want to empty the door contents and remove the whole door. I used the block, mirror and nut driver to R&R the bottom hinge plate and both cams. Time was still less than 15 minutes, Easy Fix, Thanks guys! Cheers, Ben

Per instructions in video. Super easy. Spent 45 min. cleaning ice/water dispenser and ice maker tray. Spent 15 min. replacing ice door.

Followed the DYI Video provided by partselect. Best advice, take a digital pic prior to disasembly, which of course I didn't! My cordless screw driver w/o the tip, is the same size as the screws thus no need for a nut driver.

I had two repair problems. #1- Ice door kit & #2 control bracket. I followed the instructional video and completed repair in under 30 minutes. I surprised myself and had a happy wife.

Moved the refrigerator out, unscrewed old fill tube, pulled it out, placed finger-screw on water line, screwed it on, put in new fill tube, re-screwed fill tube in place, put refrigerator back into place. Done!

I saw a video of it, and simply took apart the ice maker and put the new Auger Drum in, then reassembled the ice maker.