4KSRS22QDW01 KitchenAid Refrigerator - Instructions

Read the instructions, watched the video and followed the very clear instructions and lay out.

Repaired it using the video that you sent through email. Thank goodness for the video or would still be trying to fix it!

When I ordered the new auger drum from this website, I noticed a video that explained how to install the item. When I received the new drum, I went to the website and found the video. All I did was to watch the video and do what the repairman did. I did get a little confused when I noticed that the auger in the video was metal, and mine was plastic. However, upon removing the pieces as shown in the video, it became clear that the new auger drum would fit the same way the broken one had fit. After that, it was a snap to put the pieces back together.

Went to the site to determine the problem and ordered the three most probable causes to my situation. replaced two of the items and had to send one part back because it didn't exist on my Model. Still did not run. Went back to the site and ordered the thermostat and the problem is resolved.

Replaced the Crisper Drawer Cover and Shelf Frame with the new one - less than 4 minutes. Thanks for sending me the exact part.

Followed recommendations from others but went with most likely by percentage = defrost timer kit. Did not solve issue. Then went with bi-metal thermostat and that did not fix the problem. Tested the thermostat as recommended on line and old part was bad, new part ok. Then I saw on line that I should have listened for fan operation. I checked and found the fan motor to be defective. Replaced the motor and refrigerator worked fine. Both the motor and bi-metal thermostat were required. Should have checked fan operation first.

Followed the instructions on package, went extremely well, with no problems what so ever! Thanks so much for the part and how to do list!

The drawer just had to be replaced.

This was not a through the door unit. The water dispenser is located inside the refrigerator. Unplug the refrigerator. Remove the two screws holding the cover over the dispenser parts. Could not remove the cover completely as there is a water supply line attached. Let the front of the cover down as far as you can get it. The micro switch is reachable. Move plastic retaining posts holding the switch in place, to the side to release the switch. This can be done with your fingers. Pop the switch out. Use the blade of the screw driver to gently pry the electrical connection plug away from the switch. Attach the new switch to the plug and put everything back in the reverse order of disassembly. Done, easy, even I could do it.

very simple ! Just follow the instruction video on parts select . It don't get any more simple than that ! Learned a lot just watching that video . I picked up from that how to install an ice maker also . I cant believe I paid a repairman $100 last year to install an ice maker on my refrigerator either . I could have done it myself for 1/3 the cost and still had a brand new ice maker . I asked him about fixing the ice bin then he said they was no way . Said the best thing for me to do was try to find a used one would probably cost me about $100 . I think the total cost for the parts was about $30 here . And BTW takes about 2 min to change out an ice maker . I will never call another repair man to come into my house again unless they do away with the internet .

After figuring out online what I needed I was sent the step by step video on what to do. I have never did anything like this but I learned. In the Past my husband would deal with it but he is no longer alive to do this kind of stuff. Thank goodness you sent the video along with all the instructions as i had my laptop on the table and followed stopped it and followed it again. I actually did this . I am so proud of myself.Thank you for making it so easy.

The fix was easy. I jacked up the unit and put on blocks. I used socket and ratchet removed the wheels. Reinstall new ones and let off the blocks.

Using a pair of pliers position the nose perpendicular to the inner wall of the ref and grip tight on the flat part of the support stud and twist counterclockwise until it become loose. Once loosened pull the support stud outward until it clears the the hole. Installation: Slide the support stud in and twist it hand tight. Using a vise grip and locking the jaw just tight enough to hold it firm on the flat parallel edges twist them (one at time) clockwise until it feels tight the tongues are parallel to to be able to slide the shelf support.

I took ice bin apart to ensure what part I needed. Got Serial # & Model # from inside fridge. Online search for Whirlpool Parts to check out prices. Settled on PartSelect for best price. Quick service too!!! Before putting it all back together, I reviewed the video. It was pretty good. Just left it up & after each couple of steps, I'd look at what was next. Went together with no problem. There could have been more details given, like ensuring that certain things lined up during reassembly. There was dead time when the narrator could have given pointers.

Removed the two lower drawers and crisper frames as would normally be done to clean. After cleaning, replaced as normally would substituting the broken frame with the replacement. If I hadn't cleaned them and only replaced, it wouldn't have taken more than three minutes.