Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 4KSRF42DTX2

4KSRF42DTX2 KitchenAid Refrigerator - Overview

Get Parts and Repair Help for 4KSRF42DTX2

If you know the refrigerator repair part you need, you can browse the list of all parts on the 4KSRF42DTX2, or you can search by name or part description. You can also find your part by where it is located on the 4KSRF42DTX2 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for 4KSRF42DTX2 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$65.25

Icemaker Control Assembly

This part is used to help tell the icemaker what to do - it turns the timing cams and the ejector blades. Motor is not sold separately.

$19.27

Ice Bin Auger Drum

This white ice bin auger drum comes with a washer.

$7.40

Water Tube Kit

This tubing is 1/4'' in diameter and comes with 2 inserts. This tubing may be longer than the original, and may have to be cut.

$46.85

Evaporator Fan Motor Kit

This refrigerator evaporator fan motor kit comes with a wiring harness and a four-inch push on fan blade.

$31.47

Roller and Eyelet - Kit of 2

$5.00

Plastic Tubing Inserts - 4 Included

These inserts are used with 1/4 inch plastic tubing.

$14.88

Ice Dispenser Guide

$13.70

Nut Assembly

This nut and insert assembly is used for plastic water lines in refrigerators.

$17.97

Lever Spring

$4.80

Shelf Support - Left or Right Side

Also known as an end cap. This part is sold individually and is used to keep the shelf trim in place on the door of your appliance.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

No ice

  • Customer: Daniel from Suwanee, GA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 430 of 511 people found this instruction helpful
removed flap door in front of icemaker...removed 3 screws with bolt heads...removed one additional screw with bolt head and ice unit slid out. I removed motor unit (pops out no screws). Replaced and had ice within 3 hours. read more

My refrigerator stopped cooling and the freezer section stopped freezing

  • Customer: garth from forest lake, MN
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 172 of 190 people found this instruction helpful
I knew the chances of all the freon leaking out was unlikely so I looked at the wiring to the compressor and there was a capacitor and a starter/overload so i figured I would start there. I went on line and found the parts at this site and they were less than the minimum service call charge for a service tech so I figured what the heck let's give her a shot ... read more

Plastic bits dispensed from Ice Dispenser in Door

  • Customer: john from seaford, VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 160 of 173 people found this instruction helpful
Removed Ice bin from Fridge

Removed all bolts on bin with nut driver...about six

Removed housing...be careful with spring on crusher/cube control rod

Removed C clamp on end of auger with small slotted screw driver and needle nose pliers.

Removed plastic nut on end of auger shaft

Removed Ice crusher jaws ... read more