4KN15E1XMR0 KitchenAid Mixer - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Screw cracked on the front of the mixer
-
Mrs Brenda from LYNNWOOD, WA
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken gears
-
walter from SOUTH ELGIN, IL
-
Difficulty Level:Very Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bad speed control
Thank goodness for YouTube. Pretty much followed the process of taking it out. Was easy, but having a video made it a bit simpler.
Parts Used:
-
Thomas from LILBURN, GA
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
PLANETARY WAS FALLING OUT
First you need to remove the aluminum ring around the housing by using a Phillips screwdriver and removing one screw. You will then have 4 screws around the housing to remove. Once the screws are removed lift the housing and set aside. At the front of the machine there is a housing that encloses the gears. Remove the 4 screws, lift the housing and set aside. At this point you will see the gears and on the shaft there is a snap ring that needs to be removed. Once the snap ring is removed tap the shaft down and remove it from the bottom. To assemble insert the new planetary and reverse the steps to reassemble.
Parts Used:
-
GREG from LA PINE, OR
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Splash from K45 KitchenAid Mixer Bowl
The shield works sufficiently. Note that the shield is not a continuous circle as shown in the picture. This actually can be an asset because it can be installed or disassembled without stopping the mixer of having to lift the head while running.
Parts Used:
-
Mark from LEXINGTON, SC
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
unit would only operate at high speed
using Phillips screw driver, remove 5 screws - take off cowl (cover)l. remove 2 screws holding speed control assembly
unplug old speed control assembly (4 plugs) and plug in new speed control unit - reassemble cowl .
unplug old speed control assembly (4 plugs) and plug in new speed control unit - reassemble cowl .
Parts Used:
-
EBEN from WEST PALM BCH, FL
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Stripped Gear Mixer would not mix
I have replaced so much on this mixer I can take it apart in my sleep. # speed controllers and now 2 gears. just wish we still had the 40 year old mixer we had, never half as many problems. New are not made like the old.
Parts Used:
-
Robert from PEORIA, AZ
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The mixer started making a loud knocking noise
Unscrew the top and remove it , 4 more screws to remove the top of gear box , wipe out the old grease , lift the gears , but to remove the center gear you need a special narrow tip plier to remove the snap ring . Changed the center gear , apply new food grade grease and with reverse order putting back all remaining parts . Worked fine .
Parts Used:
-
Reza from STAMFORD, CT
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
REPLACE SPEED CONTROL SWITCH
-
FRANCISCO from SAN BENITO, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Speed control would go from a "mix" setting 1 to a whip setting "10" by itself.
When I ordered a replacement assembly, I was sent a "new" replacement. As I had read up on your site to number the 5 wires BEFORE I removed them, this was a great idea. The new assembly was wired differently than the original board. Although no install instructions came with the new part, it was just a matter of connecting the NUMBERED wires to the new configuration. The first time I fired it up after plugging everything in, nothing happened! I removed all the plug-in wires and reinstalled to ensure I had not gotten a tight connection because of the plastic covers over the end connectors. On my second try, everything worked as advertised! VIOLA!!!! It was a bit tough because of the tight spaces within the motor housing and the new wire routing. Just take pictures of the area BEFORE you disconnect anything and you should do o.k., since I did. 20 minutes.
Parts Used:
-
Joe from CASTLE ROCK, CO
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Mixer speed control was not connecting properly.
Found a kitchen aid repair video. Found your site for the part I needed. The connections were not like what the video showed but there were enough connector symbols that I was able to understand where they needed to connect. Marking the connections helped for making the new connections when the new circuit board came.
Parts Used:
-
Eileen from GREEN BAY, WI
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Speed switch bad and Initially thought new part was wrong!
At first thought part was incorrect as the electrical connection tabs on the circuit board were not inline as the existing part. However, upon closer examination I realized that the same quantity of tabs existed on the new part and although not inline, were clearly marked the same as the original part. Unit was easily replaced and is operating just like new.
Parts Used:
-
Richard from Harrodsburg, KY
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
I stripped a couple of gears due with a batch of very hard dough
Taking apart the machine is really easy. I was worried the grease would have spilled all over the places, but when the machine is cool, the grease is solid, so no spill. Replace the parts is quite straightforward, and there are plenty of tutorials on line. The only tip is that the grease used by KitchenAid is dark, and it is not easy to see all the small parts when you take the gearbox apart, so pay attention at what you do and at what you throw away... when I got to put it back together I missed a special concave washer which must have been trapped in the grease. Other than that... it has been an easy repair, the mixer is back up and running and I saved a ton on $$$
Parts Used:
-
cosimo from EL CERRITO, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:1- 2 hours
-
Tools:Screw drivers, Socket set
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The white enamel coating was breaking off the mixer beater. There was a scrapimg noise when the beater was in motion.
I simply inserted the new beater into the mixer to see if it scraped the sides of the bowl. It fit perfectly and didn't scrape the bowl like the old one did.
Parts Used:
-
Carolyn from LEXINGTON, SC
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Gear housing cracked, gear had nic in it
Removed old housing, pulled spring clip, slide on new gear and replaced clip. Put on new gasket and housing. Replaced outer cover. Done.
Parts Used:
-
Bob from ELIZABETHTOWN, KY
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!