Models > 4KMTW5755TW0 Maytag > Instructions

4KMTW5755TW0 Maytag Washer - Instructions

All installation instructions for 4KMTW5755TW0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 4KMTW5755TW0
31-45 of 220
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Washer would'nt spin

  • Customer: Dean from Poplar Grove IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 7 of 7 people found this instruction helpful
diconnected water supply and discharge, unplugged the unit, removed the aggitator, laid the washer on it's back, romoved the hoses from the pump, took out 3 bolts, removed the motor/transmission and replaced the clutch and put it all back together.

Washer would not spin a full load.

  • Customer: Ralph from Newbury Park CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 8 of 10 people found this instruction helpful
!. Removed agitator from inside
2.Removed outside cabinet
3 Removed pump, motor, and transmission.
4. Slid the entire drive unit out of the tub from the bottom
5. Removed the clutch assy. and installed new.
6. Reverseed the procedure to re-assemble.

stopped working only filled with water.

  • Customer: Christa J from ElDorado Springs MO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 8 of 10 people found this instruction helpful
Fast simple and supper easy! Please do not waist your time or money on repairmen that rip you off. You are garunteed all the way or your money back from Parts Select. Go to your model number than read a few stories of others to better pin point your problem then order part and your item will ship fast I had my part on the 2nd day of the order. Do not be fooled you can do it easily! I have order twice and both items went smoothly and took less then 10 minutes to put in. Thanks Parts Select for making it possible for the little guys and supporting them and not the big rip off scammers. I will be back when needed. May you continue in your good deed! C.S.

washer wouldn't start up after filling & closing lid

  • Customer: Jeremy from Marengo IA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 8 of 10 people found this instruction helpful
First I loosened the 2 screws on the outside of the top control assembly with a philips screwdriver. Then I took out the 2 other screws toward the top on the back with a socketwrench.Next I removed the top so I could access the switch. After that I removed the broken switch and unhooked from wire hareness. I then hooked up the new switch and snapped into place. Last I put the top back on and screwed into place.

Replaced ring that broke and washer that was bent on the edge.

  • Customer: Kim from West Liberty OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 16 of 35 people found this instruction helpful
Took the agitator out and gearbox off unhook wires from motor and take off water pump, replaced the parts and put back together. Pretty easy to fix. However, I still haven't got my problem fixed. Originally the washer wouldn't spin after the rinse. I put on a new coupler and it worked for a few loads, then something smelled hot and started stinkin the house up so I opened the washer lid and smoke rolled out. Turned it off. Took the moter off and checked it and it would barely turn at all. Replaced the motor with a new one. Still wouldn't spin. Put on a new clutch assembly. Still wouldn't spin. Bought a new capacitor thinking that would do it. Still don't SPIN!!! (The ring and washer I replaced was just a casualty, not any of the problem).

Machine agitated during cycle but would not spin clothes dry.

  • Customer: Kurt from Bremerton WA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 7 of 9 people found this instruction helpful
Followed the excellent video instructions. They say you can perform the repair without removing the enclosure, but when I saw how easy it was to remove it, it definitely improves the access and speeds the repair. Have a piece of wire handy to to hold the pump assembly out of the way. Installed new clutch kit and it runs like a champ.

Tub did not center and seal was hanging out of tub

  • Customer: James from Nelsonville OH
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Socket set
  • 7 of 10 people found this instruction helpful
Laid washer on front side and removed top spring, then lifted the tub assembly to replace the right side spring, the one behind the motor was the hardest, I lifted the tub then removed the spring bracket at the tub with pliers and a socket. The top seal all I had to do was take the 4 screws that hold the top on (it takes a long extension) then sit it bak up and I lifted the top up to give me enough room to unsnap the top piece of the tub, cleaned it up put seal in. The parts fit perfitlt and real fast shipping, I bookmarked the site and will buy from again. JIM

washing machine will agitate but not spin

  • Customer: Robert from Manchester CT
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench set, Wrench(Adjustable)
  • 13 of 28 people found this instruction helpful
I removed the cabinet and agitator, layed the machine on it's back, removed the pump, motor and gearcase. I found a way to prop the gearcase up so it rested level, removed the cover, drained the old oil. I removed all internal parts, disassembled them and cleaned them. I reassembled the gearcase using the new uetral drain assembly, and replaced the oil. I made sure the brake assembly was pushed into position and then put the gearcase, motor and pump back in. I sttod the machine up, put the cabinet back on and tested the machine. It still did not spin, so it wasn't the coupler, clutch or nuetral drain assembly.

washer would not agitate when lid was closed

  • Customer: Timothy from Saint Louis MO
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 6 of 7 people found this instruction helpful
The only tricky part was figuring out how to get to the part. There were only two screws that seemed likely candidates to pop off the control panel (on the back at the corners). Fortunately for me the obvious answer was the right one...the panel lifted up and the new part went in - very easy.

Leaking discharge hose

  • Customer: wayne from webster KY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 7 of 11 people found this instruction helpful
removed old hose clamps and hose using pliers. Installed new hose which had all new clamps preinstalled on new hose.

Washer basket off-center and wobbling during spin cycle

  • Customer: Craig from Woodland Hills UT
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 5 of 5 people found this instruction helpful
Remove the washer case/enclosure to expose all the internal parts. Lie on the floor and with pliers and a strong arm. Remove and replace each spring one at a time. Pretty straightforward.

tub oscillation

  • Customer: leonard from phil campbell AL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 7 of 12 people found this instruction helpful
placed washer on side and installed new pads
and returned washer upright

Washing machine shakes violently during spin cycle

  • Customer: James from Asheville NC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 13 of 30 people found this instruction helpful
Removed four screws that hold the top control panel to the base and hung over the back panel in order to remove the main wrap-around body of the machine. Took off top plastic ring fastened to side of tub then removed old Balance ring. Installed new balance ring. Unfortunately, this did NOT fix the problem. This was a suggestion from Justanswer.com and failed miserably. Does anybody know how to fix this problem? And it's not the springs or the little plastic shims around the base OR the cross coupling to the motor...

drain hose for washer was cracked and leaking

  • Customer: richard from orange CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 5 of 7 people found this instruction helpful
This was really easy and the part came in like 2 days. All I needed to do was flipthe washer on its side and remove the old hose...a couple screws and install the new one...it was a perfect match so ...no issue.

Severe wobble during spin cycle.

  • Customer: Steven from Dallas GA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 5 of 7 people found this instruction helpful
After removing the 2 phillips screws at the base of the control panel, I flipped the panel toward the back. Using a screwdriver, I popped off the spring clips, releasing the cabinet. I removed the 1/4" hex head screw on the spring mount and removed the old spring and replaced with the new. I repeated this with the other 2 springs. The spring bracket in the rear also holds the tub balancing spring. It is easily replaced while replacing the suspension spring.
If this didn't fix the problem, we were going shopping for a new washer. After this repair, it operates like new!
All Instructions for the 4KMTW5755TW0
31-45 of 220