Models > 4KHTW4505TQ0

4KHTW4505TQ0 Washer - Overview

Parts and Repair Help for models starting with 4KHTW4505TQ0

If you know the washer repair part you need, you can browse the list of all parts for models starting with 4KHTW4505TQ0, or you can search by name or part description. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for 4KHTW4505TQ0 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Models starting with 4KHTW4505TQ0

$3.32

Agitator Directional Cogs

These agitator directional cogs are commonly referred to as dog ears. They come four to a package and are usually used with direct drive washing machines.

$11.77

Direct Drive Motor Coupling

This coupling kit is used between the motor and the transmission on direct drive washers with no belt. This is the newer version and is made with new metal sleeves for added strength.

$29.84

Direct Drive Water Pump

It is intended for use with washing machines that do not have belts. This drain pump has two ports for water to pass through: a large one, and a smaller one.

$2.52

Suspension Spring

Sold Individually. Appliance takes 3 of this part.

$28.77

Clutch Assembly

A worn clutch can cause a slower spin speed which will leave your clothes wet after a cycle. This clutch assembly comes with brake cam driver, blue spring for large capacity wash...

$21.75

Lid Switch

The pin on the lid pushes on the lever of the lid switch to tell the machine that the lid is closed. This part includes the grounding wire.

$4.46

Agitator Bolt

This kit contains one screw with rubber gasket and threaded sealant. The screw head is 7/16".

$2.52

Thrust Spacer

This white thrust spacer is made of plastic and is also commonly referred to as a retainer ring. It is used in the agitator assembly of many direct drive washing machine models. This is the retaining ring for inside of agitator. May need agitator grease for repair.

$3.76

Tub Spring

$24.40

Agitator Repair Kit

This six piece agitator repair kit comes with a four inch cam, a thrust spacer, and four dogs ears (agitator cogs). This kit is used to move the upper agitator and it connects the base of the agitator with the agitator top (mover).

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

REPLACE WATER PUMP COUPLING

  • Customer: RICHARD from PHILA PA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set, Wrench set
  • 485 of 492 people found this instruction helpful
REMOVED CASING TIP OVER WASHER DISCONNECTED WATER PUMP. DISCONNECTED MOTOR THEN REPLACE COUPLING THEN REASSEMBLE MOTOR THEN REPLACED WATER PUMP. read more

washer wouldn't agitate

  • Customer: mike from Kent WA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 474 of 478 people found this instruction helpful
First pry off the cap of the agitator. Then using a socket remove the bolt that holds the plastic cup in place. Remove this cup by prying it loose from the two tabs that hold it in place. Once this cup is removed you can get to the broken cogs.
Slip the new cogs into the underside of the cup, and slide the cup back down in the agitator housing usin... read more

Washer not agitating

  • Customer: Craig from Polk City FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 461 of 461 people found this instruction helpful
On top of the agitator is a flat cap that is held in place by the friction of an o-ring, there are no fasteners. I would imagine one could get under the lip with a small screwdriver or butter knife to pop it off but I chose simply using my fingernails so as to not disfigure the cap. Under the cap you will find the head of the only bolt that holds the assem... read more